Jump to content
SAU Community

Aircon Cleaning

Mick

By Mick,
in General Maintenance

 Share

Recommended Posts

Mick Mentor

Mick

Posted
Posted

hey i melted a huge hole in my aircon hose under the hood when i had my screamer pipe on and i didnt realise for quite a while, i knew it stopped blowing cold air but i still used it to just blow air a few times and the heater still works fine so i had run that quite a bit with this big hole melted through the silver insulated aircon hose. Anyways i have got a new hose to put on it and i will then get it filled back up with has cos obviously its empty but im worried about all the crap that would have got inside that big hole, everytime it has been turned on would it have sucked and blown all that crap inside it all? and if so what would i need to clean exactly?

would it have gotten into the aluminum canister or into the unit in the dash, the aircon is totaly empty so i can safely open stuff up but in not sure where i would need to clean

Link to comment
https://www.sau.com.au/forums/topic/454663-aircon-cleaning/
Share on other sites
Ben C34 Grand Master

Ben C34

Posted
Posted

If the air con has no gas in it it doesn't actually turn on the compressor, so it wouldn't have pumped stuff through.

Stuff would have just got in on its own free will, probably wouldn't have got out of the hose into other bit. See what the air con guy says.

Link to comment
https://www.sau.com.au/forums/topic/454663-aircon-cleaning/#findComment-7494926
Share on other sites
89CAL Grand Master

89CAL

Posted
Posted

If you are truly worried they can do a flush. As Ben said, the A/C compressor has a trinary switch that turns it off above a certain pressure and below a certain pressure. As soon as the hose started leaking the compressor would have cut out and never started again. Air con systems need to be clean, but I dont expect too much would have got into the system (bar the melted pipe which has been replaced anyway)

Link to comment
https://www.sau.com.au/forums/topic/454663-aircon-cleaning/#findComment-7494951
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      PXL_20250828_063541093.TS.mp4
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • PranK
      R35 GT-R production ends after 18 years

      By PranK · Posted

    • SteveL
      Leak from Tokico BM50 Brake Master Cylinder

      By SteveL · Posted

      I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...