Jump to content
SAU Community

Recommended Posts

Event:
Happy Laps - Queensland Raceway
Description:
A chance to get out on track for a fun cruise and have some om nom noms! Bit of spirited driving is allowed but it is still an event on a race track so a few rules need to be followed (see below). Also if you have not done QR before this is your ticket in to Lakeside.
Location:
Queensland Raceway
Date:
Sunday the 12th of April.
Time:
7:00 AM Arrival
Cost:
Slight change in the payment form these happy laps onwards:
$35 for members and guests of members who pre pay by direct deposit
$40 for members who pay on the day
$50 for non members
Please note that this is a per person cost, any passengers etc are required to pay as well.
Requirements:
1. QR have a minimum age of 12 for passengers.
2. No overtaking in the first 2 laps.
3. The overtaking car is responsible for completing the overtaking move safely.
4. Overtaking is only permitted on straights, unless clearly waved passed by the car in front.
5. Overtaking move must be completed well before the end of the straight, and the car being overtaken must be given plenty of room.
6. Cars should not be more than 2 abreast at any point on the track.
7. Be aware of cars around you, in front and behind (and beside when being overtaken).
8. Do not assume that the car in front of you knows you are there.
QR RULES

10. There is to be no racing

11. The straights are speed limited to 120km/h

12. Any car that goes off the track will be pulled off

13. There is not to be more than 1 sec of tyre smoke.

14. There are to be no helmets

15. Vehicles must have current registration and number plates are not to be obscured in anyway

Payment Details:

Name: Skylines Australia Queensland Club

Bank: Westpac

BSB: 034 063

ACC: 354012

PAYMENT REFERENCE: Username&HappyLaps

Attendees:
  1. Cadmoon +1
  • 2 weeks later...
  • 2 weeks later...

Got in car of the event+second camera for second half that i'll upload over the next little while. Got some footage of Ant'z car shooting flames also Ralphs (footage was better for his, and have 2 views)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...