Jump to content
SAU Community

Recommended Posts

Garage sale. pickup location 2087 sydney forestville or Ryde (working horus). most items can be shipped, buyers expense.

lets start with the good stuff.

R34 gtt neo highflowed turbo (14psi adjustable actuator) - $600 not nego

I pulled 257rwkw and 660nm with supporting mods on 18psi BP98 dyno sheet provided.good pull, good condition, good response, minimal shaft play if any.

R34 gtt neo stock turbo - $200

No shaft play good condition.

GFB Responce dual port BOV - $200 not nego

good condition can be set to atmospheric or plumb back Used for approx 1 month

Nistuned r34 gtt neo ecu- $400

has a existing tune 257rwkw can be overwritten.

Greddy profec spec 2 - $200

works perfectly. comes with solenoid-cables

autobahn88 Rb25det metal intake - $100

fits with pod no silicon included.

Genuine r34 skyline floor mats 5 - $150

r34 gtt neo stock airbox with snorkle - $100

r34 gtt neo AFM - $50

Cometic upper intake gasket - $30

R34 gtt neo engine cover - $50

r34 gtt stock intake pipe metal breather pipes - $30

Pair of federal 595 tyres 265/35zr18 - $100

prob 50% thread left?

post-133245-0-37857900-1427602217_thumb.jpg

post-133245-0-29543200-1427600908_thumb.jpgpost-133245-0-71822500-1427600949_thumb.jpgpost-133245-0-29058200-1427601033_thumb.jpgpost-133245-0-96701000-1427601129_thumb.jpgpost-133245-0-80628300-1427601174_thumb.jpgpost-133245-0-84517200-1427601273_thumb.jpg

post-133245-0-70503300-1427601303_thumb.jpgpost-133245-0-07311300-1427601381_thumb.jpgpost-133245-0-20395200-1427601547_thumb.jpgpost-133245-0-32071400-1427601672_thumb.jpg

Edited by mike_nazz

Im the 2nd owner i put about 7000km on it. not sure how many km he put on it.no issues. Prev owner said he got it highflowed by turbologic by someone called fred. He also said its got garrett internals.

No receipts

Edited by mike_nazz

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Was going to say the car pulls up nicely everywhere, especially going into that last long right hander before the main straight. Looks like a lot of fun.
    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
×
×
  • Create New...