Jump to content
SAU Community

Recommended Posts

Hi guys/girls, kinda new to the forum, I've stalked a lot but that's about it haha.

Question is what timing belt kits have you run, any bad/good experiences and what brands, I'm due for a timing belt kit and water pump, my pump will be genuine but when it comes to the kit I'm not sure which to go, there a few brands out there, found kudosmotorsport.com gives u a few options of belt brands. My car is a street/drift car mainly, comes out to play once a month of money allows but gets driven most weekends to the shops and maybe to race track to spectate, qld laws are making me scared to drive it hahah

Edited by Lamsr334door
Link to comment
https://www.sau.com.au/forums/topic/456044-rb25det-timing-kits/
Share on other sites

I run a Gates racing belt with no problems. Some people find they are noisey but they may be over tensioned

Kudos offer Greddy as well i think which i havent heard anything bad about. Id probably go Nismo if i had to choose but the gates belt came in the kit i got so went with that

Thanks for advice mate, few friends have said go the gates aswell hahaha never heard anyone say they wine but as u said they have probably over tension them, and yes was checking out kudosmotorsport.com and they offer a few ranges of belt brands, most expensive being Nismo then trust/greddy

Yeah I've found mine is fine. People probably hold the tensioner tight as they do the bolt up, where as all you actually need to do is wind the engine over (backwards or forwards, cant remember) a few times then change direction, hold the tensioner at that point as you do it up. The small hex in the tensioner isnt for doing the belt tight, just for holding the tension.

Mine hasn't snapped, slipped or made any noise so must be alright. I have the procedure here somewhere anyway. that was just off the top of my head

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...