Jump to content
SAU Community

New Wasteland Wa Topic

Hattori Hanzo 69

By Hattori Hanzo 69,
in WA Wasteland

 Share

Recommended Posts

Beyond Blue R33 Mentor

Beyond Blue R33

Posted
Posted

I have to go to the pool at least 3 times a week for the back. I normally do excersize and stretches in the hot hydro pool then go to the 25m pool for walking and swimming laps. I've got dodgy knees too and if I walk too much in the pool they ache real bad but it's only Austio arthritis. I was in and out of physiotherapy for years and just pissed it all off did a load of research and found a balance that works good for me. What is the main problem with the knees?

A few of my mates I played footy with had Osgood/slaters and it finished them. After over 200 games of footy I wish I'd never played but I loved it alot. Football is my family's religion! But I've lost interest over the last few years. Not as hardcore as t-revs with his West coast Eagles engine bay!
  • Replies 16.5k
  • Created
  • Last Reply

Top Posters In This Topic

  • t_revz

    4187

  • ElleAli76

    2512

  • shoey85

    1445

  • Beyond Blue R33

    1294

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Manne
Manne

She got tinted!!

t_revz
t_revz

OMFG just had the funniest moment.   Sanae asks me if ive been washing my filthy greasy hands in the kids bathroom sink as there is black spots that wont come off no matter how much she trie

z00key
z00key

Just got back from dr (had harmony test, test for down syndrome) everything all good and found out sex, its a boy! Yeah

Posted Images

Beyond Blue R33 Mentor

Beyond Blue R33

Posted
Posted
Yeah not bad. How was the drive home car still good and did ya hav3le a grin going home thinking I got a 12 sec car

Hey Dean I found a awesomeness little R35 on Gumtree for the boy. Would post the link if I knew how. Have you got any of the r/c's up and running?
  • Like 1
R33kizza Experienced

R33kizza

Posted
Posted
1 hour ago, Beyond Blue R33 said:


DSC_0348.JPGDSC_0347.JPGthe earlier time was the faster. Dropped it to 30 psi all round today. Do you think the duramax 75-90 is the right oil for the diff? It was juddering bad when I changed it then came good with the l.s.d. Paste and figure of 8's? The tein basics have only height adjustment and the ride is hard as since I lifted I't?

Track temp definatly didnt help, colder it gets the less sticky it becomes and less traction u get. Same principle when its too hot.

Diff oil sounds about right, was the old oil burnt? Id day that the shock from spinning the tyres to it gripping proberly caused it to tighten up through heat. New oil and a some maneuvering always helps.

Ur shocks are gonna have more travel due to increased hight, more fluid to move bk and forth within its stroke which will make it feel harder

  • Like 1
Beyond Blue R33 Mentor

Beyond Blue R33

Posted
Posted
Track temp definatly didnt help, colder it gets the less sticky it becomes and less traction u get. Same principle when its too hot.
Diff oil sounds about right, was the old oil burnt? Id day that the shock from spinning the tyres to it gripping proberly caused it to tighten up through heat. New oil and a some maneuvering always helps.
Ur shocks are gonna have more travel due to increased hight, more fluid to move bk and forth within its stroke which will make it feel harder

Hmm makes sense, that's what I was thinking too much extension and not enough compression in the shocks which would coincide with the longer travel and higher spring rate. When you gradually build up the boost and launch it sweet on the street is the only time you notice it. The old diff oil was clean as. I was also thinking due to getting cold between runs that it was at its minimum viscosity but the thinner the oil it should make its way into clutch packs better?
t_revz Grand Master

t_revz

Posted
Posted

Football is my family's religion! But I've lost interest over the last few years. Not as hardcore as t-revs with his West coast Eagles engine bay!


I watched footy in high school and early twenties. Now I despise it. I'd rather watch netball or lawn bowls
  • Like 2
t_revz Grand Master

t_revz

Posted
Posted

i watched WM on youtube. there is 26 x 22minute episodes plus there is a movie

 

i enjoyed the series more than i expected. initial D was better but its still very good. the movie isnt bad from memory either

  • Like 1
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • tidi0x
      Wheel Sizes & Offsets For Skylines

      By tidi0x · Posted

      Wanted to add some of my R33 GTST  R34 GTR wheels, 18x9 ET30 with 255/35/R18 PS4S'   BBS RE-V7 029 18x9.5 ET22 with 255/35/R18 PS4S' Needs a bit of camber   
    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      Lamb roast on Saturday will be different 🥲
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • GTSBoy
      RB25DET with solid lifters - which cams ?

      By GTSBoy · Posted

      I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...