Jump to content
SAU Community

Replaced Speedo Now The Power Steering Is Heavy ?

adam wicks

By adam wicks,
in General Maintenance

 Share

Recommended Posts

adam wicks Collaborator

adam wicks

Posted
Posted

I recently replaced my speedo cause the other broke in my Nissan skyline r32 gtst 1993. The new speedo all works, when the car is started the power steering works fine but after a little drive for about 30 seconds if that the steering goes heavy?

I've had a read about some sensor but I have no idea where it is and what to do about it ?

Any help would be great thanks

Hadouken Grand Master

Hadouken

Posted
Posted

Have you back tracked? Ie

Take the cluster back out and check all connections. Apparently the sensor is at the back of the dash and the steering angle sensor is in the column.

Put the old cluster back in and see if you have power steering back.

Process of elimination.

Check your power steer reservoir.

ErOR Contributor

ErOR

Posted
Posted

The sensor behind the dash is the one coming from the gearbox. It's a big round hole with a small shaft sticking out of it right behind the gauge cluster. That's where the speego gets its reading from. Funny that your speedo works but you get heavy steering as usually when that pin breaks and car no longer receives a speed signal is when you get the heavy steering.

You might have to do a HICAS diagnostic test and see what comes up.

ErOR Contributor

ErOR

Posted
Posted (edited)

Have you had a look at the fuses?

All I could point my finger at this point is some kind of a bad connection...

Since you're using a lock bar like me, do you have anything unplugged from hicas ecu? Silver box under the parcel tray.

To get into HICAS diags:
1) Switch ingition off, transmission in neutral or auto in Park.
2) Start engine
3) Very quickly (with a couple of seconds), turn the steering wheel left and right about 20 degrees from centre five times, and then pump the brakes five times, then press the brake pedal once more - this will enter diagnostic mode.
4) Drive forwards or backwards about 5 metres at a speed less than 10k/ph, this will enter full diagnostic mode.
5) The HICAS light in the instrument cluster will be flashing quickly (for normal) or will flash a code indicating any problems. Long flash = first digit, short flash = second digit. Diagnostics will return to normal after five minutes, or any speed over 10k/ph, or ingnition is turned off.

Result codes:
11 HICAS control unit
12 HICAS motor power supply not present
13 HICAS motor output not present
21 Vehicle speed sensor not present
22 Steering angle sensor not present
23 Steering angle sensor neutral or not present
24 Rear main sensor input not present
25 Rear sub sensor input not present
31 Parking brake sensor input not present
32 (Auto) Inhibititor switch input not present
(Manual) Neutral switch input not present
33 Engine speed signal not present
Edited by ErOR
adam wicks Collaborator

adam wicks

Posted
  • Author
Posted

The lock bar was installed by the last owner so I'm not sure but I've owned the car for about a year and never had a problem till I replaced the cluster, I'll do the diagnostics and see what happens, I did an ecu diagnostics and it was all okay

jiffo Mentor

jiffo

Posted
Posted

What sensor are you testing?

The item on the column behind the steering wheel is the steering angle sensor and since you've deleted HICAS I can's see it having any input.

You swapped the dash and then your troubles began so to me it's a speed sensor problem.

The actual speed sensor is just a reed switch built into the speedo right where the cable enters.

There's differences between early/late models, so could be a wiring issue.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      I forgot about my shiny new plates!
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...