Jump to content
SAU Community

Recommended Posts

I have a 1995 R33 GTR, and have been noticing oil coming into the intake pipe between the rear MAF and the rear turbo.

Someone suggested it could be from the exhaust crankcase ventilation (PCV) connected to the rear intake pipe, so I installed a catch can between the pCV and the rear turbo. However, the oil is still showing up in the rear MAF intake hose. I see oil coated on the turbo side of the MAF.

I have twin BOVs recirculating back to the Y pipe between the turbos, and when I rev the engine, I can see the air coming back out of the rear MAF (and not the front). The front MAF and turbo intake pipe are clean, which makes me think that the oil might be coming in from the rear turbo. This theory however, seems to suggest that the rear turbo may be leaking and blown.

However, the car boosts fine, all the way up to 1 bar without any hesitation. If the rear turbo was blown or had issues, would the car still boost? There is no oil leak under the car, and no black or blue smoke coming out of the exhaust. It idles fine as well.

I am totally stumped. I dont want to push the car if the rear turbo is blown, because some people have suggested it might be, but then others say that if it were, I wouldnt be able to boost the car to 1 bar.

Any ideas or suggestions to check?

Please help me as I want to make sure that the car is fine.

Thank you,

Munib

Link to comment
https://www.sau.com.au/forums/topic/459082-1995-r33-gtr-oil-in-intake-pipe/
Share on other sites

The blowby that gets sucked out of the head by the turbo (As opposed to the drivers side which goes into the engine on over run) goes to the rear turbo. This is almost certainly what you are seeing. Usually it ends up dripping out of the bovs. Even the crack pipe priced Nismo catch can doesn't stop it from happening.

So how does one discern if it is the blow-by oil or the turbo is shot/leaking oil from the compressor side? If there is a compressor oil seal leak, will it also go into the intake piping? If so, how do we determine what is actually happening without removing the turbo piping?

Also, if there is an exhaust oil seal leak, will that also cause the oil to come up front of the turbo towards the compressor and go into the intake piping?

Surely, there would be a way to identify if the oil is from the blow-by or the turbo oil seal leak....?

In addition to this, I do not see any oil at all in the catch can....maybe a tiny droplet, but that's all. And while the car is running OR I am revving the engine, I do not detect any suction from the catch can into the hose I am running to the rear turbo-MAF intake pipe. If this means the turbo is not spinning, it wont be sucking in any air from that hose, could this also be causing the recirc from the BOV to come out of the rear MAF? When I let go of the accelerator, I can see air/oil blow out of the rear MAF filter. This has me perplexed.

If it is just blow-by coming back from the BOVs, and oil is returning with it, why is it escaping though the rear MAF only, and out the rear filter, and getting sucked in by the turbo since the whole point of recirc is to keep the metered air within the intake system?

I dont know if what I am saying makes sense....the BOVs recirculate air, it comes back into the MAF-turbo pipes (through the Y-pipe that connects to both turbos), and ideally, should at stage be sucked back in by the turbos. Instead, it is escaping out of the rear MAF...

If it is just blow-by coming back from the BOVs, and oil is returning with it, why is it escaping though the rear MAF only, and out the rear filter, and getting sucked in by the turbo since the whole point of recirc is to keep the metered air within the intake system?

I dont know if what I am saying makes sense....the BOVs recirculate air, it comes back into the MAF-turbo pipes (through the Y-pipe that connects to both turbos), and ideally, should at stage be sucked back in by the turbos. Instead, it is escaping out of the rear MAF...

That is just because of the stock setup it takes the easy way out

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
    • What ECU are you running? This is probably the biggest question. If it's a PowerFC, I'd probably change the ECU and get something newer that will handle the injectors in a nicer way.
×
×
  • Create New...