Jump to content
SAU Community

Recommended Posts

hi all! just wanted to say hello again, I joined SAU 6 years ago but since then alot has happened and

I sold my Skyline R32, which I regretted.

Now i'm back with my fresh new import!

I've been wanting to get another R32 for a while, and found this 1993 GTS-T with genuine 67km on the clock!

It seems like it had a few minor mods like Greddy Strut brace, ARC super induction box, Sickspeed oil reservoir (still dont know what it does)

and aftermarket intercooler.

Look forward to making it a daily driver, not after ridiculous power, and want to leave the engine alone as much as possible.

I like a quick spooler.

planning on a Nistune + Z32 AFM upgrade with a HKS 2530 if I can find one..... but seems non existent these days,

If anyone has any sggestions, please let me know

post-76154-0-58630700-1440997242_thumb.jpg

post-76154-0-44411800-1440997257_thumb.jpg

post-76154-0-19487000-1440997274_thumb.jpg

post-76154-0-13398400-1440997476_thumb.jpg

post-76154-0-15165200-1440997549_thumb.jpg

post-76154-0-50127500-1440997561_thumb.jpg

post-76154-0-97074700-1440997613_thumb.jpg

post-76154-0-27324700-1440997626_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/459359-back-again-with-a-new-ride/
Share on other sites

get an alarm system, dash mat, and use a sun reflecta on your windscreen when parked up outside

you have a good dash pad so may as well keep it good, mine has just started to bubble in the vinyl and I'm pissed orf about it.

I dont think I will, its not like i'll boost unnecessarily in town,

I think turbo timers are rarely needed for a daily driver to be honest

Anyone have tints on their car?

I heard its pretty good for uv protection and heat minimization as well..?

I've read up on some articles and most will probably agree the rb engines don't have the greatest design when it comes to the reliability of cas.

What would be the most cost effective way of reducing this problem?

Would it be worth installing a trigger wheel of some sort?

The car starts fine when cold,

But when it's been driven for a while it seems to take longer to start thereafter, so hadouken suggested a possible cas issue.

I just wanna see if there are any options before I go out and buy a new cas that costs around $500 just to see it have problems in a year or two

Go post in the NZ forums and see if there is anyone near you how has an rb20 in good working order and is prepared to help you fault find. Then you can start swapping bits over in a process of elimination.

there's a fellow in the forced induction forum that sell his own design triggers, he's one option, but first have you to make sure that the cas is the fault.

Edited by Missileman

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...