Jump to content
SAU Community

Recommended Posts

Hi guys,

Just had brake pads changed and disks machined on my 2007 370GT coupe, and soon I am starting to have the annoying squeal noise at low speed to full stop and reversing particularly. Do you all have the squeal noise? What brake pads would you recommend for good performance and quietness?

Any advice is much appreciated.

Cheers

Leon

Link to comment
https://www.sau.com.au/forums/topic/459406-370gt-brake-pads/
Share on other sites

Sorry about the stupid question, how do you know the dust? Can you see it from the disk? Mine is brand new Akebono pads ( not bad reviews), not sure if it is the dust that causes the squeal noise. Normally in the morning it is the worst when reversing, as it goes and warm up, still has the noise but gets better.

Some pads make squealing noises. Usually those pads are high performance and have a usable range which is higher and that's why in the morning you hear it the most. You should get pads which are usable from low heat range to high where possible. All depends how you drive as well. I drive like an asshole so my brakes are usually always pretty hot.

Yep, what Colin said. As for how do you know the dust, I'm guessing you mean how do you know how much dust the pads are producing. It's pretty simple really. Just look at how dirty your rims get a few weeks after cleaning them. If there's not much dust, then they don't produce much dust. ;)

  • 1 month later...

I use DBA 4000 series slotted discs and EBC red stuff brake pads. Excellent performance for the wild driver (me) and no squeal.

Max, I have decided to go EBC red stuff! After two months it is still making the noise when cold, time to change. I don't want to change the full set yet as only the rear are having the noise. My front Akebono pads are only two months old. Is it ok to just replace the rear with EBC red stuff?

Thanks for your input.

post-77895-14443806589269_thumb.jpg

If it's only when cold, chances are you might still cop it with the EBC brakes too. I bought them for their stopping power and minimal dust under abuse. So far, I've been fortunate to go squeal-free but on a cold morning just rolling out of the garage, they do give a little vibration until they've warmed up after a couple stops.

If you still decide to go ahead with them, no harm in just replacing one end for the moment. It'll feel better than what you already have but once you do the fronts, where most of the braking power is, you'll want to stop more than you speed. :P

...not really. ;)

Oh no.. was having all my hope on this.. Guess it is common for the performance pads. My Akebono pads are the same and it still stop after few hard foot. I will do more research then. Are your slotted disks better than the original for heat? I also remember you have said your Megan racing muffler sounds amazing in another thread. It is on my list as well. I am following you.. haha.. Thanks for your help Max!!

Oh no.. was having all my hope on this.. Guess it is common for the performance pads. My Akebono pads are the same and it still stop after few hard foot. I will do more research then. Are your slotted disks better than the original for heat? I also remember you have said your Megan racing muffler sounds amazing in another thread. It is on my list as well. I am following you.. haha.. Thanks for your help Max!!

It isn't a definite thing with performance pads but it is certainly possible. Like I said, I've gone squeal-free with mine, even when cold, but others have had the slight cold squeal. Unless it's happening every time to apply the brakes across the entire temperature range, it's hardly annoying enough to be an issue for me. As another example, I use Bendix Ultimate pad on my shitbox Ford wagon with DBA4000 series discs. I get zero squeal out of them. However, a friend did the same to his XR6 ute and he gets a squeal at low speed. He breaks balls about it because mine doesn't do it but he doesn't seem to understand that it's just luck of the draw.

Slotted discs are beneficial for removing dust that normally gets trapped between the pad and the disc, giving your pads better bite. I don't know if they do anything for temperature so much because on my roughest days, I've managed to warp a set of DBA4000 slotted after around 12,000km on my Maxima back in the day.

If you want to keep the temperature down, you use cross-drilled discs. HOWEVER, don't waste your money on cross-drilled. You're not driving a race car, smashing your brakes in from > 200km/h at bends every 200m. The holes inevitably develop fractures which is a sign to throw them out not long after. Slotted is the most you ever need to go in my opinion, even if you drive like a bastard like I do at times. It used to be all the time, which is why I managed to warp those discs so soon, but traffic these days is bad enough in Sydney such that there's nowhere to speed your bum off anyway.

As for the muffler, beauty is in the ear of the beholder. I like cars that sound tough but I can't drive them all day with that horrible drone in the cabin. The Megan Racing muffler gives the vehicle a nice note without being obnoxious. Others here have other preferences which you should check out too.

  • Like 1

Relax dude. We all share our experiences here. No difference. I'm not always this verbose, typically when someone doesn't bother searching through existing threads, much to their offence. Screw 'em.

Edited by The Max

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm looking for some real world experiences/feed back from anyone who has personally ran a EFR7670 with a 1.05 exhaust housing or a .83 I'm leaning towards the .83 because its a street car used mostly for spirited driving in the canyons roads. I"m not looking for big numbers on paper. I want a responsive powerband that will be very linear to 8000 rpm. I dont mind if power remains somewhat flat but dont want power to drop off on top. The turbo I've purchased is a 1.05, although the mounting flange T3 vs T4 and internal vs external waste gates are different on both housings, I not concern about swapping parts or making fabrication mods to get what I want. Based on some of the research I've done with chat gpt, the 1.05 housing seems to be the way to go with slightly more lag and future proofing for more mods but recommends .83 for best response/street car setup. AI doesn't have the same emotions as real people driving a GTR so I think you guys will be able to give me better feed back 😀   
    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
×
×
  • Create New...