Jump to content
SAU Community

Recommended Posts

Hi, it's been a while since I have been on here but am back due to getting a new car.

I'm getting a M35 Stagea 250T RS four with leather interior, elec front seats, and while face dash gauges (speedo etc) and the car is stock unmodified from Japan.

Question is, from everything I have tried to find has indicated that the RS model didn't come with leather interior and elec seats.

So is there something I am missing or this is normal?

Also looking to get some nice VIP style wheels for it, preferably in 20" style to fill out the massive guards.

Can anyone recommend places, forums or shops around brisbane who deal with this?

Only moved to QLD at the start of the year.

Any help would be greatly appreciated ?

Link to comment
https://www.sau.com.au/forums/topic/459451-m35-stagea/
Share on other sites

White faced gauges means a Nismo cluster, so that's a good thing.

As for interior spec; the RS is generally lower spec; but you can option any model, with virtually any combination of optional equipment.

The wheel arches will absolutely eat up a 20" wheel; but the ride won't be too special once you do that.
I reckon 19" is probably the optimum, but personal taste dictates.

I'm sure some QLD'ers will chime in with recommended workshops, so I'll leave that.

Welcome to Stagea life.

Link to comment
https://www.sau.com.au/forums/topic/459451-m35-stagea/#findComment-7598365
Share on other sites

So nismo cluster being a good thing but K's wrong?

Wouldn't the kms be from the ecu/computer rather from the dash itself if this was the case?

It's all electronic so where are the kms stored?

Ecu or dash cluster?

This is all new to me hence why asking

Link to comment
https://www.sau.com.au/forums/topic/459451-m35-stagea/#findComment-7598511
Share on other sites

So nismo cluster being a good thing but K's wrong?

Wouldn't the kms be from the ecu/computer rather from the dash itself if this was the case?

It's all electronic so where are the kms stored?

Ecu or dash cluster?

This is all new to me hence why asking

The Nismo cluster could have been fitted at any time during the cars life; so the Odometer may not be a guaranteed starting point.

It looks nicer than the stock cluster, and doesn't stop at 180km/h (doesn't change the speed limiter though).

Mileage is stored on the cluster; hence the comments.

If the car is in good condition; there's probably not much to worry about, but if you want to know for sure; there are places that can verify the mileage of the car prior to it leaving Japan, for less than $100.

It's more about peace of mind than anything.

Pulling off a rocker cover and checking the condition of the head and cam lobes will tell you pretty much everything you need to know about the engine.

Link to comment
https://www.sau.com.au/forums/topic/459451-m35-stagea/#findComment-7598554
Share on other sites

Ok

Well I believe it was checked in Japan before being brought over here.

Then the car was complianced in Melbourne.

The car will go over the pits next week at regency in Adelaide.

Surely through all that it would be checked to some degree?

Also has a nismo badge under the RS four on the tail gate if that means anything or not - I don't know.

Thanks for your information though.

Much appreciated.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/459451-m35-stagea/#findComment-7598603
Share on other sites

There's no obligation for any of them to verify the Km's. You can ask them to give their personal opinion based on the inspection but I can guarantee you the ignorant comments will be along the lines of "All imports have dodgy kms" and, "it looks pretty good, but no way to know for sure". Despite having more stringent regulations than Australia, most people will still make those comments. The reality is, it's more likely that a car purchased locally has dodgy km's than a direct import now. Dozens upon dozens of dealers have been embroiled in wind backs covering all makes and models, at least there is a measure for Japanese imports.

The best thing you can do is check relatively obvious things, seat wear, carpet wear (can be masked by new floor mats), brake wear (could have been replaced or could have just been retarded and used EBC pads for street use), shocks, bushings (usually a good indication as it requires high attention to detail most people don't bother with) and then known fail points, turbos, timing belts, leaks and physical wear in the engine. Late 90s nissans were notorious for yield in turbo manifold studs around 120-140,000km, clues like this can demonstrate the true age of a car but it can all be covered up.

The positive side: The fact that people are aware of the prevalence of odo tampering with certain imports that arrived through particular dealers has driven the import price right down below their true value (just look at the cost of importing Vs local), this means, even though the Km's on the odo show XX,000, and it's probably XXX,000, you're paying the price for XXX,000 anyway, so there's actually no loss. It just means for you, you need to be aware Km's are probably higher and you should consider bringing forward preventative maintenance. These cars are a lot stronger than a lot of local crap and an extra 50,000km probably wont hurt it.

The negative side: For those of us who import ourselves, paying a premium for the assurance of Km's we end up losing further through artificial market deflation; but this is the reality of the Australian import market. The government wont have a choice but to step in and change legislation when they open up the import market, but until then imports a fringe group that have little impact on the overall auto industry.

Link to comment
https://www.sau.com.au/forums/topic/459451-m35-stagea/#findComment-7598633
Share on other sites

Some interesting points there nickrussel.

You would think that the quality of imports coming into the country would have to be relatively good considering these days.

People are after more for less and people get picky when buying a car.

If importers can't sell cars due to issues or minor imperfections then it costs them as they loose profit or end up stuck with it.

So the quality of car would have to be quite high as the simply can't afford to have issues and makes bad business sense.

Do Japanese export certificates give enough detail into a car's history?

I can't read Japanese so unless I can get someone to interpret one, the information is useless to me.

Link to comment
https://www.sau.com.au/forums/topic/459451-m35-stagea/#findComment-7598783
Share on other sites

Jump onto Japanese History check's facebook page, there's some really good advice on what to look for. It's hard to tell exactly what is genuine these days as there are dealers selling vehicles with forged dereg certificates.

Imports are still a niche market, the dealers know what cars they can make a good profit on and at the rate they bring them in it's cheaper to bring in a wreck and a high km grade 4 car then swap out the interior than importing a legitimate low km car. Low km cars in Japan are still fetching a reasonable premium as they're still desirable locally. I went in to importing a stagea thinking I would easily get one around 50,000km but they were all significantly more expensive than a car with 80,000km. Even for the money I've paid mine will only just get on road for similar to locally available models in dealers. Makes you wonder, when a dealer can turn a profit on a car that has the same price as a private importer.

As the others have said, I wouldn't be too stressed if it all looks the goods, but just stay well ahead of maintenance.

Link to comment
https://www.sau.com.au/forums/topic/459451-m35-stagea/#findComment-7598855
Share on other sites

There's no obligation for any of them to verify the Km's. You can ask them to give their personal opinion based on the inspection but I can guarantee you the ignorant comments will be along the lines of "All imports have dodgy kms" and, "it looks pretty good, but no way to know for sure". Despite having more stringent regulations than Australia, most people will still make those comments. The reality is, it's more likely that a car purchased locally has dodgy km's than a direct import now. Dozens upon dozens of dealers have been embroiled in wind backs covering all makes and models, at least there is a measure for Japanese imports.

The best thing you can do is check relatively obvious things, seat wear, carpet wear (can be masked by new floor mats), brake wear (could have been replaced or could have just been retarded and used EBC pads for street use), shocks, bushings (usually a good indication as it requires high attention to detail most people don't bother with) and then known fail points, turbos, timing belts, leaks and physical wear in the engine. Late 90s nissans were notorious for yield in turbo manifold studs around 120-140,000km, clues like this can demonstrate the true age of a car but it can all be covered up.

The positive side: The fact that people are aware of the prevalence of odo tampering with certain imports that arrived through particular dealers has driven the import price right down below their true value (just look at the cost of importing Vs local), this means, even though the Km's on the odo show XX,000, and it's probably XXX,000, you're paying the price for XXX,000 anyway, so there's actually no loss. It just means for you, you need to be aware Km's are probably higher and you should consider bringing forward preventative maintenance. These cars are a lot stronger than a lot of local crap and an extra 50,000km probably wont hurt it.

The negative side: For those of us who import ourselves, paying a premium for the assurance of Km's we end up losing further through artificial market deflation; but this is the reality of the Australian import market. The government wont have a choice but to step in and change legislation when they open up the import market, but until then imports a fringe group that have little impact on the overall auto industry.

So what do you mean by "could have just been retarded and used EBC pads for street use"?

Link to comment
https://www.sau.com.au/forums/topic/459451-m35-stagea/#findComment-7598859
Share on other sites

With a nismo dash and a nismo badge(probably stuck on much later) you may be lucky enough to have scored a nismo ecu also. Would be worth having a look

Good point actually.

The other thing I'd be doing; is once you have it in your hot little hands; I'd be doing ALL new fluids and filters throughout.

I know the compliance places are supposed to do everything; and some may well do, but draw a line in the sand where YOU know everything is done right, and you'll just be able to enjoy a fantastic car.

Link to comment
https://www.sau.com.au/forums/topic/459451-m35-stagea/#findComment-7598928
Share on other sites

I have asked the importer to provide me with a copy of the auction sheet and the de-rego/export certificate for this car as what Japanese History Check and Japanese Odometre Check would get.

All details check out to be correct with 85,413km on auction sheet so this is good peace of mind.

So the Ecu is in the front LHS kick panel yes?

What differences would there be if this was a nismo ecu over standard?

More power, better tune, more tuneable?

Link to comment
https://www.sau.com.au/forums/topic/459451-m35-stagea/#findComment-7598978
Share on other sites

ECU is directly in front of the glovebox; bolted up on the firewall. There's a plastic cover which hides the A/C fan; pull that down and look up from the footwell.

The left kickpanel contains the trans ECU.

Link to comment
https://www.sau.com.au/forums/topic/459451-m35-stagea/#findComment-7598997
Share on other sites

So what do you mean by "could have just been retarded and used EBC pads for street use"?

They're very hard pads and chew through discs abnormally fast. Makes it hard to gauge brake wear because you don't know how long they've been in there.

I didn't notice the difference when I swapped the green stuff out for bendix pads in my brembos. No doubt if I drove hard for more than 30-40 minutes there'd be a huge difference, but it's an expensive waste for street cars.

Tony, it's still worth doing a check with an independent company and most legitimate importers will support you doing that to improve the integrity of the industry. At the very least read up on all the stuff about how to check the documents are legit.

Link to comment
https://www.sau.com.au/forums/topic/459451-m35-stagea/#findComment-7599181
Share on other sites

Tony, it's still worth doing a check with an independent company and most legitimate importers will support you doing that to improve the integrity of the industry. At the very least read up on all the stuff about how to check the documents are legit.

Do you know how to read them?

Could just post them up on here or pm to you?

Link to comment
https://www.sau.com.au/forums/topic/459451-m35-stagea/#findComment-7599202
Share on other sites

Nah, I've just been reading up on how to check the authenticity of the documents.

This facebook page gives you a fair bit of info.

https://www.facebook.com/CarsImportedFromJapan/posts/1552399758374634

A few of the other companies also give tips and tricks on what to look for with the documents too but that page has more than enough info. If it passes that test I'd be pretty confident, just don't lose the certificate because it seems very few people hold onto them and it could limit your market.

Link to comment
https://www.sau.com.au/forums/topic/459451-m35-stagea/#findComment-7599449
Share on other sites

Even if the k's look close on the last two shakken results, they only store the last two in their system apparently, which can be another issue altogether.

With a Nismo dash that was never a factor option, you can be guaranteed it's out, but do you really want to know by how much? Almost every import owner I know has relied on the fact they are all wound back, and goes by condition rather than K's.

Link to comment
https://www.sau.com.au/forums/topic/459451-m35-stagea/#findComment-7599555
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
×
×
  • Create New...