Jump to content
SAU Community

Recommended Posts

hi all,

i just went to Wollongong from Sydney today. on the highway with up hill,20-25% flatting on acc pedal, car speed around 100km/s - 110km/s, i always get fuel cut when injector load at 25%-30% (4-5psi on boost), when the issue came, injector load down to 0% then back to normal, sometimes injector load will up to 40%-50% then down to 10% then back to normal. (i got this info from greddy informeter touch). engine will not stall, just got one second fuel cut then back to normal and continue speed up.

when i keep rev up with 20%-25% flatting on acc pedal, after the car got fuel cut and restore back, it will happens again after several seconds. i need to release my right foot then depress again to speed up again.

i just did the main maintenance, change all oil/fluids, new plugs, transgo kits, hiflowed turbo (with EBC runs 17psi), turbosmart kompact, kn oil filter, new fuel filter, constant 12v on stock fuel pump (just blew the walbro pump), 4 new tyres (same size) for about 10000kms (actually there is no shudder when driving on flat highway over 100km/s or brake)

there is no problem if the road is flat or 10% flatting on acc pedal (absolutely it is going slow down when on up hill road).

after back home, i scanned with consult3, there is no error code.

i am not quite sure when i have this problem but i just found it today, LOL. (there is no much up hill highway in Sydney...)

may be the problem is stock fuel pump doesn't contact 12v? any ideas? or time to get emanage?

Edited by YangLIU
Link to comment
https://www.sau.com.au/forums/topic/460888-fuel-cut-when-go-up-hill/
Share on other sites

The additional load from the hill causes higher boost vs tps vs rpm than the ecu will allow(boost cut). Duty cycle decreasing shows the ECU cutting fuel not the fuel pump having and issue.

Do you run a Throttle controller ?

Matt

The additional load from the hill causes higher boost vs tps vs rpm than the ecu will allow(boost cut). Duty cycle decreasing shows the ECU cutting fuel not the fuel pump having and issue.

Do you run a Throttle controller ?

Matt

Yes, I have throttle controller in my car

I do have a throttle controller. Using the throttle controller normal map fixes it half the time. Changing the max AFM output voltage on my EMU fixes it all the time

i am thinking how stock ecu get rid of this with stock turbo

Lol, trifecta

besides throttle controller, is there any help if i remove EBC and swap back factory boost solenoid?

you mentioned "Changing the max AFM output voltage on my EMU fixes it all the time"

for my problem, when i got fuel cut, it was under low boost and i assume my stock AFM didn't get 5v voltage at that time. why changing max AFM output voltage could fix this problem?

Edited by YangLIU

It's not a 5v cut, it depends which cells you are in as to what the AFM cut voltage is.

If you are hitting 21 odd psi occasionally and still have the stock map sensor connected it can boost cut as well.

Just bumping the boost up on the factory map will cause the ecu to protect the engine, sounds like you are trying to destroy it from 3 sides so don't be surprised if you have gone backwards in power. tuning time is well overdue.

It's not a 5v cut, it depends which cells you are in as to what the AFM cut voltage is.

If you are hitting 21 odd psi occasionally and still have the stock map sensor connected it can boost cut as well.

Just bumping the boost up on the factory map will cause the ecu to protect the engine, sounds like you are trying to destroy it from 3 sides so don't be surprised if you have gone backwards in power. tuning time is well overdue.

i have stock map sensor on the car but blocked the vacuum. anyway, will get tune soon.

btw, is it necessary to get emanage ultimate or just need emanage blue? also is there any plug and play loom or just need universal loom?

so many questions. :nyaanyaa:

The Blue only adds timing and fuel I think, the Ultimate adds and subtracts.

You need to hardwire the universal harness, either into the stock loom or I can supply a patch loom if you really don't want to cut wires. Not cheap, but I could prewire that for you I suspect, and send it out ready to plug in.

The Blue only adds timing and fuel I think, the Ultimate adds and subtracts.

You need to hardwire the universal harness, either into the stock loom or I can supply a patch loom if you really don't want to cut wires. Not cheap, but I could prewire that for you I suspect, and send it out ready to plug in.

PM sent. :rolleyes:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Resizing injectors in Nistune can be done a couple of ways, and there are a couple of ways that you can make a mess of it. The tuner needs to be really aware of the effects of whichever approach he uses (either K, or TIM). They are both easy enough to "get the injector size right" to run the engine. But little details like old start enrichment and hot start are affected differently, depending on which boxes you check.
    • Pretty safe to say almost everyone that has tuned their own car has experienced this issue. The difference being that we have our laptop in the car and when it happens, it's literally 10 seconds of tuning to sort it.  Would you be happy to plug in your laptop and sort this yourself? It is a very simple process and there is no risk of harming your engine (if you are worried about that). 
    • Yeah thats the next step now, either they wil or i will take out for a drive to work and go straight their after work and see is we get the same issues 🤞  thought i try my luck here too, never know someone else might have had the same issue but thanks for the reply 
    • Basically your tuner needs to drive it for the 30 min (or whatever) to create the same conditions then check the ECU settings and sensors at that time. They may not be excited to because that takes them 30 min rather than just opening the bonnet and seeing the problem straight away.... Hot start is generally not as tricky as cold start, but there would be a table for fuel enrichment vs coolant temp as a starting point
    • Yeah, they all cant say anything for sure as everything is working fine . Said unable to find an issue untill it stops again. Could mist likely be CAS wiring or IAS valve issue but again not 100%
×
×
  • Create New...