Jump to content
SAU Community

Recommended Posts

I recently installed a wideband in my s1 c34 stagea. I cut the power and earth from the clock and used those. Now my problem is, now my dash doesn't store the trip a and trip b kms traveled, it just wipes it every time I turn the car off. Is the memory for that run through the clock loom somehow?

Link to comment
https://www.sau.com.au/forums/topic/460990-trip-meter-memory/
Share on other sites

they don't have to be run through a relay. It is just like wiring any other gauge or head unit. a afr gauge is not going to draw that much current to warrant a brand new power run from the battery.

using the clock is a interesting one for a power source. the fuse probably blew while he was tampering with the wires.

they don't have to be run through a relay. It is just like wiring any other gauge or head unit. a afr gauge is not going to draw that much current to warrant a brand new power run from the battery.

using the clock is a interesting one for a power source. the fuse probably blew while he was tampering with the wires.

my innovate diagram said to specifically run through a relay. along with everyone with an innovate

here is the install from the manual. If you read carefully it does not say you "must" use a relay. Says if in doubt. And draws 3 amp, your cigarette lighter draws more lol

Connect the RED wire to an isolated switched 12V source in your vehicle. A switched 12V source goes ON as soon as “key on” power is active. The circuit to which you will pull power from should be able to support a 3 amp draw. Make sure this connection is protected with a 5A fuse.

Circuits that share power with the vehicle’s stereo, ignition system, ECU, lighting, or fuel pump should not be used. When in doubt, create an additional circuit using an automotive relay available at any automotive parts supplier. See the next section for a relay installation diagram.

The BLACK wire should be grounded to a solid ground source. The best possible ground source would be the battery ground (-) post.

  • Like 1

Yeah hadouken I must have done it when I was moving wires about when I was in there with the test light. That circuit has a 10A fuse, and given the wiring was already there and that's where I wanted to mount my afr display anyway, it made sense to tap into it. And as I've already found out, if it does trip the fuse, only the trip reading and clock are affected so I can still drive the car.

post-55653-14473263497916_thumb.jpg

Edited by fmlycar

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
    • Probably. I take it that they are also mentioned to be for R34 Skyline? For example.... RDA has that part as RDA7957. I have the dimpled and slotted version of that on my car https://www.ebay.com.au/itm/285518478694?srsltid=AfmBOopKxMuAFpsxZJdB1cam4D5RAj1f9yJyOttPZLAwXVNCOiwlhrIy This is DBA's top one piece equivalent https://www.ebay.com.au/itm/364246686631?srsltid=AfmBOorbb0XHQgqTvZLgQPhg70nqJtGvdojKnugum3O2LFSr2h-obp8D  
    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
×
×
  • Create New...