Jump to content
SAU Community

Recommended Posts

ok just changed the rear cradle on a s2 rwd auto stagea to the narrower s14 cradle

i have adjustable camber arms in

toe is -15mm on both sides, i need longer toe arms

i was told that when i got adjustable toe arms to also get traction arms

car is not overly low

question is, do i really need to get traction arms?

was going to run a street set up from this:

http://www.nissansilvia.com/forums/index.php?showtopic=317341&view=findpost&p=4301102

ie:

Recommended Road Settings
Front
Caster = 7 degrees positive (slightly more on the LHS to counter the drift to the gutter)
Camber = 1.25 to 1.5 degrees negative
Toe = Zero

Rear
Camber = 0.75 to 1.25 degrees negative
Toe = In 2 mm each side

Link to comment
https://www.sau.com.au/forums/topic/461371-when-are-traction-arms-needed/
Share on other sites

traction arms are always needed otherwise your car will crash to the ground. HA. HA.

adjustable ones help with reducing bump steer when you lower the car, so you need them if you have noticed a bump steer problem and want to spend some time on an alignment hoist dialling it out.

or, you could just chuck them in, adjust them to % of stock length based on how much you shortened the camber arm by and feel like it improved things like most people do

  • Like 1

What's 'not overly low' more specifically?

If you drop the car from standard heights to anything more decent it's probably lowered an inch or more, and you might want to change the traction arms too. eBay arms are <$100, you'll spend more than that in one proper alignment.

You can definitely run without, I did for years. Putting in adjustable traction arms did help with bump steer a little, however the main culprit turned out to be a busted shock on one side.

No fking way you would drive it with 15mm toe out per side. I presume you still have the standard eccentric bushes but no way can they get that much adjustment. You will scrub out your tyres in a few hundred km if you drive it in the current state.

Sorry haha, was late and I obviously wasn't reading correctly.

I don't know how advantageous it would be running aftermarket traction arms in a street car. Personally I would but if you track it sometimes and are semi-serious about it, then it's probably worthwhile.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...