Jump to content
SAU Community

R34 Gtt Wont Idle

Ry_R34GTT
 Share

Recommended Posts

Ry_R34GTT Apprentice

Ry_R34GTT

Posted
Posted

Hey so i have googled and searched through the forums quite a bit and would still like a second opinion. For a while my 34 was having coil pack issues, one cylinder not firing occasionally and sounding like a truck/loss of power. The other day i was driving as per normal and all of a sudden under throttle i was losing all power and felt like MASSIVE drag so i pulled over. At this point it was idling fine and would rev through the rev range perfectly but once in first gear id take off normally and after about 2 meters it would have a huge power loss and drag. I managed to get the car home 2 meters at a time as i didn't want to leave it on the street (really bad area) and then had to reverse up my drive way as it was the only way i could get it up there ( too much power loss in first but not in reverse). I let it sit for a bit and now when i start it it starts perfectly and then dies straight out. If i giver it some throttle it is fine but is spitting out black soot and will stall once it hits idle.

After hours of research i came up with the either AFM was not working, vacuum leak or faulty idle switch. So i pulled it apart the AFM and re soldered it and still no good. My question remains is the AFM faulty or is the idle switch faulty? any ideas? :D

Kinda losing my mind haha

Link to comment
https://www.sau.com.au/forums/topic/462964-r34-gtt-wont-idle/
Share on other sites
SE skyline Rookie

SE skyline

Posted
Posted

So were 5 wet?

Was it running than you removed them so they could have gotten wet. Plugs that work will not be wet because they burn the fuel. If it was running rough than you pulled plugs than they could have a chance to get fuel on them on the cylinders that are not firing.

SE skyline Rookie

SE skyline

Posted
Posted

I had one stuffed coil pack and it made my car miss fire intermittently. One spark plug looked a little different in the fouling. Because it was only sometimes it had not changed the plugs appearance a lot. I changed all coil packs as my car has done 185000km and I just bought it so I don't know when they were last changed. Either they have done a great amount of KMs or they have been changed once before as they normally last about 100000km.

Ry_R34GTT Apprentice

Ry_R34GTT

Posted
  • Author
Posted

sorry for the late reply i have been away. All the other plugs looked perfectly fine as i replaced them maybe 4 months ago or so but one was black and dry none were wet. Just before i went away i found a rather big split in one of the main intake hoses and i have just replaced that but the battery is dead so i have to wait for it to charge to see if it changed anything. :)

Ry_R34GTT Apprentice

Ry_R34GTT

Posted
  • Author
Posted

So i started her up and she started fine and went to die. Gave a little bit of throttle and she settled on idle so i let her warm up for a bit. Revs through the rev range beautifully but now at idle she sounds like shes missing occasionally so i disconnected each coil pack one by one and it sounded worse every time so the coil packs arent the problem. This problem is unrelated btw it was doing this for a week or so before she died.

Ry_R34GTT Apprentice

Ry_R34GTT

Posted
  • Author
Posted

Went for a drive and she is pulling harder than she ever has been and my boost gauge was only hitting 7 psi instead of 10? Then i popped a hose that i must not have tightened properly but i lovely lady with a 200 sx came running out of her house with tools so could get it home haha

Ry_R34GTT Apprentice

Ry_R34GTT

Posted
  • Author
Posted

I know im just a little slow haha :)

I believe all my problems have gone away now after i fixed the boost leak and cleaned the IAC Valve. No weird idle and car has alot more power but kinda feels like it pulls back slightly once it hits boost. Thanks for the advice tho Hadouken was very helpful :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Driveline vibration is resolved. I ended up loosening all my engine mount and trans mount bolts, giving it a good shake then retightening everything and it's gone... Let's just say I was surprised that fixed it.  I've been happily driving it around again but unfortunately put zero time into my direct port/constant pressure WMI setup. I'm on vacation next week, so I'll try and finalize it then.  On a different note, I spent all week fuel/ignition mapping 2x 216L V16 engines. Turbo's were burning glycol and we swapped them out for larger units. We also had planned emissions testing on site, so I figured I'd be there the same week to use their instrumentation and massage any emissions issues out if needed. This was a first for me. Fuel management is similar in certain ways to automotive (i.e air density as load variable) but very different in others. It's all PLC based and AFR's are controlled by air and not fuel. They use a control valve between the turbo and air manifold to control pressure which in turn controls AFR's. Due to this, target AFR tables supplied by the OEM are in pressures and not mass which really through me off. They use air pressure vs fuel pressure tables. I also relied on an O2 concentration sensor the emissions team had in the exhaust. Ignition timing was also all over the place and we were losing a fair bit of power. They're now happily sitting at 16-40BTDC depending on load. We were making about 1600kw at 900rpm at 90% load. Engines were running a lot smoother as well.    
    • Duncan
      1992 R32 GT-R Race Car

      By Duncan · Posted

      heh, aint no R32 ever meeting modern targa cage rules unless the driver is veeeery short OP, good luck with the sale, since its already in the land of freedom I'm sure you will find a good buyer.
    • Duncan
      Oil pan for RB25DET NEO Stagea "version"

      By Duncan · Posted

      meh, it was a good video, clear about the issue and how he dealt with it. A bit heavy on the RTV and very brave to put an RB in anything without rebuilding it first, but otherwise I thought it was good Dose, I'm not sure that having the pickup forward is a big issue; yes of course the oil could shift under brakes but the sump should never be empty enough for that to be a problem (unless you also have a higher volume oil pump, and that oil can't return from the head to the sump quickly enough)
    • MBS206
      Starting again

      By MBS206 · Posted

      I can donate $100 to your upgrade fund. So long as you can donate the IC7 my way....
    • MBS206
      Starting again

      By MBS206 · Posted

      I'd love a Haltech ECU, and Haltech 10 dash. Was having a chat with Rob and Andy @ Haltech when Rob put one in his MR2. First one I'm kind of interested in too, as you can dim it RIGHT down. Andy was saying bright dashes is one of his peeves too!
×
×
  • Create New...