Jump to content
SAU Community

Recommended Posts

  • Replies 151
  • Created
  • Last Reply

Top Posters In This Topic

This is my Cefiro. June 89 build, ~90,000kms, RB20DET, 5sp, cat back exhaust, Black, Sunroof, Nardi Wheel, Bride Brix Passenger Seat, ghey gearknob, SSR Mesh Rear wheels, unknown Dished fronts, Late Model Tail light & centre panel. Slight rear panel damage.

I have Z32 front brakes, Tein HR Coilovers, R33 GTR cooler, R32 GTR Cams & R32 GTR injectors to go in once it arrives in mid August.

JK

Link to comment
https://www.sau.com.au/forums/topic/46351-cefiro-owners/#findComment-941376
Share on other sites

Ok spose i better list my mods too.

RB26DETT

Custom turbo's equivilant to hi flo 2540's

600cc injectors

Wolf3dV4 with MAP

HKS adjustable cam gears

Aftermarket cams, unknown spec(we believe 262's)

twin pod filters

custom Dump pipes into a twin 3" system

R200 rear diff with a welded up 4.3:1 gearset

VL Turbo gearbox

OS Geiken twin plate clutch

Nismo fuel pressure regulator

Bosch 040 fuel pump

R33 gt-r radiator(modded to fit)

Hybrid bar and plate intercooler

Profec b S2 EBC

Link to comment
https://www.sau.com.au/forums/topic/46351-cefiro-owners/#findComment-941395
Share on other sites

I have a couple of Cefiro's........ a dead stock one (has coilovers, exhaust, pod and steering wheel waiting to be fitted.

And another that basically has too many bits and pieces to list.

Would post a pic but not sure how.

JAGER: Both of mine are avialble for sale if you are interested. PM if you like.

Link to comment
https://www.sau.com.au/forums/topic/46351-cefiro-owners/#findComment-941457
Share on other sites

Interior/Vinyl spray will soon fix that brown. Those wheels are pretty nice... guards look to be rolled at the front too?

Im thinking I shall be removing my grille and replacing it with an ARC oil cooler if I can find/afford one ;P

JK

Link to comment
https://www.sau.com.au/forums/topic/46351-cefiro-owners/#findComment-941559
Share on other sites

Do these come with R200 or R180?

The diff in mine looks a fair bit different to the R200 in my SR SIL80

Mine also came with R32 gtst brakes all round. Also the roll-cage wasn't bolted in at all. It was just sitting in there!.... Drift-rice!

I know that Cefiros are very widely used as drifters in Japan and NZ. Drifters in Oz haven't taken to them yet. Its only a matter of time

Link to comment
https://www.sau.com.au/forums/topic/46351-cefiro-owners/#findComment-941587
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...