Jump to content
SAU Community

Recommended Posts

Hello

I will buy a new pump soon because the one I have is old and I believe on its ways out.

The weekend, I went out and pushed my car to the limit like I have never done before.

I ran with a tuned GTR and some other cars.

I have been pushing my car within safe limits to learn how to drive the power I how and use it with tune and things I have.

The weekend I pushed it!

Did pretty well with keeping up with the gtr( he didn't floor it lol) and the other cars. But I was pushing my car to the limit.

Afterwards when doing normal driving, my car would hesitate and I lost power(not electrical power) when changing from 2nd to 3rd gear and than drive normally again. I couldn't go past 3000 rpm in any gear.

My friend adjusted the cas and the car drove better but I still have problems sometimes in 3rd and 4th gear. Sometimes it hesitates and loses power(not electrical) as I am approaching 3000 rpm and than it will be fine.

Last night as I was sitting in the car with the car idling, it cut off. I was able to restart without any problems.

Today as I was driving in 3rd gear it started to hesitate again and wanted to cut off. I pulled to the side of the road and the engine started revving as if I hit the gas. The car cut off. I started the car again and as I was pulling off it cut off again. I was going up a hill.

I started the car again and gave it some gas, the car drove fine and the engine sounds fine.

The car at traffic lights idles fine.

Yesterday I cleaned the spark plugs, it had some carbon build up along the top of the plugs.

Didn't have a chance to clean the maf because the auto stores didn't really have maf cleaner.

It seems the hesitation happens if I drive sporty. If I baby the car, it doesn't give me the problems as much.

I researched about possible causes and the number cause I found is that it can be the fuel pump. Next was the maf, coil packs, igniter, injectors.

Yesterday when checking the car, I didn't see any fuel leaks or smell gas. The car starts and idles fine.

Could it be the fuel pump? I know its old and it was starting to make weird noises sometimes before this.

You would not have done any damage to the fuel pump by caning the car. Simply would not have. So if it has died or is dying then that is purely coincidence. It is 5 minutes to test it. Just have to load the engine up with a fuel pressure gauge connected.

You ARE likely to have cooked the coil packs if you were caning the engine, because it all would have gotten hot. Same with the igniter module. The CAS and the AFM could also have suffered from heat. You need to do the standard diagnostics on all those things if you hope to discover what it is.

You would not have done any damage to the fuel pump by caning the car. Simply would not have. So if it has died or is dying then that is purely coincidence. It is 5 minutes to test it. Just have to load the engine up with a fuel pressure gauge connected.

You ARE likely to have cooked the coil packs if you were caning the engine, because it all would have gotten hot. Same with the igniter module. The CAS and the AFM could also have suffered from heat. You need to do the standard diagnostics on all those things if you hope to discover what it is.

So caning means pushing the car?

I was about to get new coil packs soon any way, spit fires. I have an extra set of stock igniters, afm have an extra but its old, and the cas, well don't have any extra.

Stupid question, how would I do the standard diagnostics on cas and igniter? Igniter, I thought either it works or it doesn't. Coil pack I thought it works or it doesn't. Can always check the voltage on each coil.

My friend who tunes cars adjusted the cas the first time after I experienced the first problem. It helped the car drive more smooth.

Yes, caning means driving it hard. As in "hitting it with a cane", a la corporal punishment from my school days.

Coils and ignition module are usually diagnosed via swaptronics with known good components, although you can also have a look at running coils in the dark to look for obvious spark leakage.

CAS is obviously diagnosed using swaptronics unless you have an oscilloscope that you can use on the dyno to watch the signals from it.

All this has been covered a bajillion times before, on this and every other forum.

Yes, caning means driving it hard. As in "hitting it with a cane", a la corporal punishment from my school days.

Coils and ignition module are usually diagnosed via swaptronics with known good components, although you can also have a look at running coils in the dark to look for obvious spark leakage.

CAS is obviously diagnosed using swaptronics unless you have an oscilloscope that you can use on the dyno to watch the signals from it.

All this has been covered a bajillion times before, on this and every other forum.

Didn't know about diagnosing a cas, never heard of one going bad. Don't have any extra to swap to check.

Took off the coil packs yesterday when I cleaned the spark plugs, they are working fine. Can always double check with a voltmeter.

I will check if I can find a used cas.

So pump is pretty much going out, but the cas might be bad.

Will check

How do you know they are working fine? You can only really test them under load.

all of my cylinders are firing. Ive already encountered what its like when a coil pack is dead. Car sounded like a Subaru as the joke around the shop went.

No access to a dyno at this time.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
    • There is a warning that "this thread is super old" but they ignore that anyway...
    • With 10% Ethanol, we're talking 2-3% fuel consumption difference. The emissions reductions and octane boost in my opinion far outweigh this almost non existent loss.    My tanks sitting at 80%. Luckily that should go down fast as I'm on vacation again for the next two weeks. 
×
×
  • Create New...