Jump to content
SAU Community

Recommended Posts

i'v posted thread befor about the coils

missfiring @ idle

i use to have it mostly when the car is cold ..

i'v changed the places of the coils ... mmm feel some diffrent .. ( dont know why )

now it miss fire lil bet ... but .. mostly .. it like losing power btween 4500 tell 5800 exactly .. only between those rev its not accelerating like it should ... after 5800 rev . it go's ok ... tell it reach 7000 ... every time it did the same .. in all gears .. (didnt try 5th gear) and by the way .. it happen some times .. some times it not ... i mean after driving for some time .. this gos off

any way

100% misfiring at idle .. but not sure if it misfire at 4500 .... (i think its somthing else)

so .. the Q is .. ?

why its only loosing power at 4500 to 5800 every time ????

is there anything special happen between those rev's ??

i really feel sick already :throwup:

plzzz help

if they r the coils that would be easy to fix ..

mod: hks filter only

Link to comment
https://www.sau.com.au/forums/topic/46618-sick/
Share on other sites

My friends car misfired between 4000rpm and 6500rpm because the spark plugs where gapped to high, we gapped them down and it was all good. Maybe check your plugs first.

...thanx for replying mate ....

i already did that ..

gap = 0.8

NGKplug IR laser iredum

heat range 6

i'v also tryed NGK R iredum

heat range 5

also did compretion ratio at home ..... its ok... lil diffrent in some of them .. (not a big deal tho)

some pic

Link to comment
https://www.sau.com.au/forums/topic/46618-sick/#findComment-945623
Share on other sites

why its only loosing power at 4500 to 5800  every time ????

is there anything special happen between those rev's ??

mod: hks filter only

Considering your mods, that is quite strange.

With most RB25DET's running higher than stock boost, the reason there is a flat spot in this rev range is b/c of the A/F ratio's getting very rich. Timing is also retarded at this point. If your coils have any fractures in the casing, it will also misfire.

Best solution is aftermarket management or a SAFC to correct the fule mixtures.

There are quite a few threads covering this topic, search around and you will find a few solutions that have worked for others in the past...

Zahos

Link to comment
https://www.sau.com.au/forums/topic/46618-sick/#findComment-945658
Share on other sites

Considering your mods, that is quite strange.

With most RB25DET's running higher than stock boost, the reason there is a flat spot in this rev range is b/c of the A/F ratio's getting very rich. Timing is also retarded at this point. If your coils have any fractures in the casing, it will also misfire.

 

Best solution is aftermarket management or a SAFC to correct the fule mixtures.

 

There are quite a few threads covering this topic, search around and you will find a few solutions that have worked for others in the past...

 

Zahos

thnx mate .. that makes me happy ..(coz i wanna belive that its only the coil :D )... if its only coils that would be ok .. i'll change the coils next month ... split fire coils or should i go for those kind of coils which comes away from the engin (check pic)

and going for powerFC soon ,.

if any one else have any other thoughts ... iwould like to know more ... thanxx guys ..

Link to comment
https://www.sau.com.au/forums/topic/46618-sick/#findComment-945701
Share on other sites

or it could be anything, some one correct me if im wrong.

steve

mm .. the problem is that it comes and gos ..

so .. still not sure .... but 100% i'd go for new coils ... but no one answered my Q .. ?!

do i go for split fire coils ....

or i go for this coils which come alone away from the plugs ... the one on the pic .. i posted befor ...

thanx

Link to comment
https://www.sau.com.au/forums/topic/46618-sick/#findComment-950522
Share on other sites

why are they 2 different spark plugs?

One is NGK IR, the other is just R. I would definately replace those plugs just from the look of them.

Gapping iridiums is ok, you just have to be carefull. The most important part is the tip, the rest is fairly durable.

Also, how tight have u put the spark plugs in?

Try insulating the coils with electrical tape aswell

Link to comment
https://www.sau.com.au/forums/topic/46618-sick/#findComment-951203
Share on other sites

I would recomend the coils that are on the firewall (the ones in your pic) as the skyline coils are prone to failure as they get so hot!

i like that idea .... but .. do u know any good coils which is ok for the r34 .. and what convertion do i have to do to the ignition wireing .. ??

that would be a good info .. :)

thnx

Link to comment
https://www.sau.com.au/forums/topic/46618-sick/#findComment-951432
Share on other sites

why are they 2 different spark plugs?  

One is NGK IR, the other is just R. I would definately replace those plugs just from the look of them.

Gapping iridiums is ok, you just have to be carefull. The most important part is the tip, the rest is fairly durable.

Also, how tight have u put the spark plugs in?

Try insulating the coils with electrical tape aswell

i know ... i did test the NGK R 1st ... then i'v checked the NGK IR ..

i will change them also .. while changing the coils .. ..

any info about the coils in the pic .... :) .. ?!

Link to comment
https://www.sau.com.au/forums/topic/46618-sick/#findComment-951436
Share on other sites

why are they 2 different spark plugs?  

One is NGK IR, the other is just R. I would definately replace those plugs just from the look of them.

Gapping iridiums is ok, you just have to be carefull. The most important part is the tip, the rest is fairly durable.

Also, how tight have u put the spark plugs in?

Try insulating the coils with electrical tape aswell

i know ... i did test the NGK R 1st ... then i'v checked the NGK IR ..

i will change them also .. while changing the coils .. ..

i dont know ... exactly ... but 100% not too tight ... i can open them and close them easly .. but i know they r not lose ..

any info about the coils in the pic .... :) .. ?!

Link to comment
https://www.sau.com.au/forums/topic/46618-sick/#findComment-951440
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...