Jump to content
SAU Community

Recommended Posts

Hi there, up for grabs I have an immaculate set of nismo lmgt4 omori edition wheels in 18x9.5 +12, they have no scuff or rash, only selling due to putting the old school lmgt1 on my r32 Gtr, they come with 265/35/18 tyres with about 60% tread, 2xachilles 123s and 2xkumho

these wheels are one of the lightest wheels and look amazing, to suit 32/33/34 Gtr, 

located in Melbourne but will post at buyers expense

price- $4000

tony- 0412862091

image.jpeg

image.jpeg

image.jpeg

image.jpeg

image.png

image.jpeg

image.jpeg

image.png

image.png

  • Like 1

Nismo omori has 2 versions the older versions have stickers and the new versions around 2015 have the laser engraved logo. The clear give away is the lip on the omori it's not stepped like the other lmgt4's

 

hope this information helps 

  • Like 1

No lay bys haha im happy to hold for a week or 2 max but nothing else at the moment, they are way too cheap so first in takes them

  • Like 1

Wheels are now off the car, as you can see they are in basically brand spanking condition no Marks no rashes or any scraping, and 2 of the tyres are federals which I did Mistake for kumho and other 2 are Achilles 123s as as advertised 

 

$3500 firm!

image.jpeg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...