Jump to content
SAU Community

Series 2 R33 GTST Selling whole or wrecking

R33gtst77
 Share

Recommended Posts

R33gtst77 Newbie

R33gtst77

Posted
Posted
Series 2 R33 GTST Selling whole or wrecking

Currently have an unregistered r33 series 2 turbo. Will sell the entire car plus an rb25det that has bad piston rings but a set of new Mahle Forged pistons and also series 1.5 parts for 6k or nearest offer. Yes I know its unregoed and you can get a turbo manual for that price but the car is complete, very clean, runs fine and is ready to go over pits but unfortunately I work 6 days a week and i cannot do it myself, the only way I can make my money back is by wrecking it, and on top of that I have too many car's so it has to go. The 33 has just under 124,000kms, nice and tidy, no one has ever smoked in it, white, front bushings have been done. the rear coilovers were gone so replaced with pedders springs with bc coil overs on front that will also need to be replaced soon. Very nice to drive and garaged for the 4 years I have owned it. If car does not sell i will then start to wreck and make my money back. Will post up pics when my computer finally decided to acknowledge my phone. Cheers

Link to comment
Share on other sites
R33gtst77 Newbie

R33gtst77

Posted
  • Author
Posted
Series 2 R33 GTST Selling whole or wrecking Currently have an unregistered r33 series 2 turbo. Will sell the entire car plus an rb25det that has bad piston rings but a set of new Mahle Forged pistons and also series 1.5 parts for 6k or nearest offer. Yes I know its unregoed and you can get a turbo manual for that price but the car is complete, very clean, runs fine and is ready to go over pits but unfortunately I work 6 days a week and i cannot do it myself, the only way I can make my money back is by wrecking it, and on top of that I have too many car's so it has to go. The 33 has just under 124,000kms, nice and tidy, no one has ever smoked in it, white, front bushings have been done. the rear coilovers were gone so replaced with pedders springs with bc coil overs on front that will also need to be replaced soon. Very nice to drive and garaged for the 4 years I have owned it. If car does not sell i will then start to wreck and make my money back. Will post up pics when my computer finally decided to acknowledge my phone. Cheers


Link to comment
Share on other sites
  • 2 weeks later...
  • 4 months later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      MLR's Bogan cruise ship

      By MBS206 · Posted

      He could just take the Bogan Cruise Ships setup... Already got a good setup, with blower, the auto was rebuilt too wasn't it? Perfect time for him to upgrade the tailshaft, diff, and axles...    And wouldn't need to waste money on redoing the Commos seats, as he could just buy race seats for the 5...   As a highly modded car he could avoid the ability to give it away to offspring too when they crash their cars...
    • MBS206
      Alcon TA6 Calipers on R33 GTST - Flexing

      By MBS206 · Posted

      It's really interesting how much it's moving left to right, and doesn't appear to be actually spreading. For this to be moving left to right, without flaring, means unequal forces being applied until equilibrium hits in one way or another.   Reasons it could be unequal; Piston sizes left to right are different sizes. Only minute differences. Pistons moving on different planes. That is, are they moving directly straight at each other, or slightly out of alignment. The fluid is restricted getting to one side.   Some tests you could do. Pull the bleeders on the left and right, fit each side with pressure gauges. It will allow you to make sure pressure is equal (and really, it should be as fluid flow is so damn low, so fluid flow dynamics shouldn't come into it).   With the calipers off the car, have both sides retracted as far as possible, measure very very accurately (think micrometre) distances between opposing pistons in four different spots per set of pistons. Firstly, on each opposing pistons pair, the measures on for different spots should be equal. If it's not, and especially if one spot appears to actually get closer compared to another, the pistons aren't aligned, and now the forces left to right won't be equal, as they're the forces fighting each other.   You can also pull all the pistons out, and very very accurately measure the diameter of them. If they're not equal left to ight in the pairings, and especially if the area of the pistons on one side is different to the area on the other overall, it'll all be out of whack.   My bet, is shit QC in making sure the pistons move in the same plane left vs right. Some minor out of square machining, and nothing will line up, things will want to move around.  
    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      Whilst putting a V8 in a MX5 would be fun, it would negate the whole cheap to run fun daily that the MX5 will be used for If I wanted a faster little convertible I would have got a engine check light, I mean a BMW Z4 M, but going off the issues that the guy at work who recently got one is having, it is lucky I didn't  Meh, horses for courses, the Bogan Cruise Ship is my go to for some horse torques    
    • Dose Pipe Sutututu
      MLR's Bogan cruise ship

      By Dose Pipe Sutututu · Posted

      I reckon give him a few months, LSX swap would be good
    • MBS206
      MLR's Bogan cruise ship

      By MBS206 · Posted

      Mark needs to get bored at work and order things on here...
×
×
  • Create New...