Jump to content
SAU Community

Recommended Posts

Tried a search but couldn't find what I was looking for.

My Xenons have been converted to halogen bulbs for compliance as with most 34s. One of the park lights(i think the one at the edge is the parker?) has gone and I need to replace it. I wanted to know what type of Halogen bulb I will need to buy to replace this and any suggestions on where to get these from?

Any specific tips for dissasembling the headlight would be great too. Thanks.

Link to comment
https://www.sau.com.au/forums/topic/46796-r34-halogen-bulbs/
Share on other sites

you should be able to take the globe out without taking the h/light apart . you can get the globe at any auto shop , take yours out and tested to make sure its the globe then buy one the same .

Link to comment
https://www.sau.com.au/forums/topic/46796-r34-halogen-bulbs/#findComment-949154
Share on other sites

hmmm, unless its one of those damn stupid 'sealed beam' headlights (i think thats what they are called)

when the compliance guy did my brothers type x 180sx, he changed the whole headlight, and its sealed, so u have to buy the whole thing, cant replace the bulb, as the whole headlight is vacuum sealed! i dont think thats what you have, but it not too difficult to spot how to take the bulb out.

Link to comment
https://www.sau.com.au/forums/topic/46796-r34-halogen-bulbs/#findComment-950491
Share on other sites

i've got h1 headlights on mine,, would so like some xenon headlights,,

anyways,, to get to the parker lights,,

u have to remove the battery or move it back atleast,, to get to the right parker light,,

some long nose plliers would help..

and to get to the left parker light,, you have to remove the intake box,,, should be bolted in 4 places,, and easy to get to.. also might have to remove the coolant reservoir tank,, 1 or 2 bolts i think,, than u can get to the parker lights easily.

the parker light sockets should be a twist on/ twist off plug,, twist left to unplug i think,,, thats if its the same parker lights as a H1 headlight..

either way, i think u'll have to remove all those things to get to the parker lights,,

hope it helps,,

AFRO

Link to comment
https://www.sau.com.au/forums/topic/46796-r34-halogen-bulbs/#findComment-953330
Share on other sites

Thanks. Any help is appreciated.

Just wanted to really know whether I would have to do some serious disassembly to get to the back of the bulb or not.

Just haven't got a lot of time to spend taking things apart and putting back together.

Link to comment
https://www.sau.com.au/forums/topic/46796-r34-halogen-bulbs/#findComment-953489
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...