Jump to content
SAU Community

Recommended Posts

Thinking of letting go of my 1996 R33 Gts-t which I have owned for 4 years.

This car is one of the last R33’s that have been kept in immaculate condition. Every modification has been performed with performance and reliability in mind. Every nut and bolt has been torqued to OEM Nissan spec as I am extremely fussy when it comes to working on cars.  All modifications were performed in the last 10,000km and nearly all parts were purchased new.

 

A general overview: 

1996 ECR33 Gts-t

122,000kms  - Genuine (have jap auction sheets)

Zero crash history

 

Engine:

100,000km Service performed (timing belt, tensioner and water pump)

Hypergear 21U High-flow turbo

JJR bell mouth dump pipe

Venom 100cpsi high flow cat

Apexi N1 cat-back system

Apexi PowerFC with hand controller

S15 440cc Injectors

Walbro 255lph fuel pump

Cooling Pro ‘No Holes’ stealth intercooler

Z32 AFM

Custom aluminium intake pipe

 

Drivetrain:

NPC Organic 10” Clutch installed by Forced Motorworks

Fresh transmission and diff fluid

GKTech clutch damper eliminator

 

Suspension:

BC BR Coilovers

Hardrace front LCA bushes

Hardrace adjustable caster arms

HICAS lock bar kit

 

Wheels:

Work Emotion XD9

18x9 +30 with Kumho KU36

18x10 +38 with Federal 595SS 

Wheels were powder coated in space blue and are immaculate with new Genuine Work decals.

 

Interior:

Series 3 R33 GT-R seats in immaculate condition.  These cost over 1k alone.

Full alarm and immobilizer

Full Genuine Nissan 'Skyline' floor mat set

JDM Clarion system

 

This car has been serviced with fully synthetic oil and Nissan filter every 5,000km without exception. All fluids including clutch, brakes and diff have been replaced in the last 5,000km. 

The car has been tuned by Chequered Tuning and currently makes 260rwkw on pump 98, or about 300kw at the flywheel. Very responsive and will chop most things on the road. 

 

Downsides are:

•Front bar has some scratches on the bottom.

•RH rear quarter has a scratch in the clear coat.

Apart from the above the paint is excellent.

 

The buyer of this car will receive a full folder of receipts totalling over $20,000 as well as dyno sheets for the tune and original Japanese auction papers.  

You will not find a cleaner, more genuine Skyline anywhere else.

Registration is included but RWC will be left up to the buyer.

This car has no finance owing, no stolen history and no written off history.

 

Inspections are welcome however no one will sit in the drivers seat until I have cash in hand. 

The price is $14,000. This is open to negotiation however stupid offers will be ignored. 

Text on 0411 582 453 or PM

20151214_181310-1.jpg

17883702_10211032865272610_5822155757226860856_n.jpg

Edited by colourclassic
Link to comment
https://www.sau.com.au/forums/topic/469979-immaculate-300kw-r33-gts-t/
Share on other sites

  • 4 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
    • Could be correct. Meter might be that far out. Compare against a known 5 ohm 1% resistor.
    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap.  (edit: I went out and did it right now, the line I had chosen did appear to have no vacuum on it, it used to go to the front of the intake, I've now completely blocked that one off at the bracket that holds several vacuum lines by the firewall.  I T'd into the vacuum line that goes from that bracket to the vacuum pump at the front of the car, but no change in the MAP readings).  Using the new vacuum line that has obvious vacuum on the hose, im still only getting readings between -6.0 and -5.2.  I'm wondering why the ECU was detecting -5.3 when nothing was connected to the MAP nipple and ECU MAP selected as the source. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
×
×
  • Create New...