Jump to content
SAU Community

Warm idle issue - Help

Binarydata

By Binarydata,
in Engines & Forced Induction

 Share

Recommended Posts

Binarydata Contributor

Binarydata

Posted
Posted (edited)

Warm idle issue - Help

Hey all, Need a bit of help. 

Been having this issue for a while, It starts having idle issues when the car is warm, usually after about 15-20 minutes, I have got videos of what it sounds like when cold idle and when the issue starts to happen. As well as NDSI logs of as the car heats up and the when the issue happens. It was at protek automotive for about a month and they didnt find anything. 

 

I replaced the coil packs with new ones it kept happening, then i replaced the spark plugs with new BCPR6E-1, then also resoldered the AFM solder joints. 

Any insight would be more than welcome. 

 

What the exhaust sounds like cold. 

Issue as it starts to happen and get warm.

 

Issue as it gets worse.

 

What it sounds like from the drive side fender. 

 

 

I really hope someone can find what the issue is, I'm getting pretty sick of this not working.

Thank you all so very much. 

 

NDSI20170420_162105.log

Edited by Binarydata
fixing youtube embeds.
Link to comment
https://www.sau.com.au/forums/topic/470127-warm-idle-issue-help/
Share on other sites
  • 2 years later...
Binarydata Contributor

Binarydata

Posted
  • Author
Posted

Hi yes, sorry forgot to post the fix. The cas on mine went bad. The post that spins was really hard to spin. Got a replacement and fixed all the issues. Later took the broken one apart and lubed up the bearings and that fixed it. Put the ex-broken one back in the car and it's been running fine since. 

After it did what was in the video it would just stall and sometimes start again, some times not. 

 

 

Hazzid69 Apprentice

Hazzid69

Posted
Posted

Cheers. Will have to look into that then. As I’ve pretty much done all the same swap outs you had done. Plugs, coils, air filter replaced a few cracked vacuum hoses all to no avail. Was just about ready to pull the maf apart to look at solder joints but might check the cas first 

  • 4 weeks later...
Hazzid69 Apprentice

Hazzid69

Posted
Posted

Cheers mate. 
 

recently bought a consult and plugged that in. Came up with 15 faults for maf sensor and one for knock sensors but says 0 starts in brackets??? so got me a second hand maf and I cleaned out the throttle body while I had the piping apart. That was filthy. All seems to be going well now. I’m going to hunt down the knock sensors to see if they are properly connected and the wiring is in good condition as from what I’ve read the sensors are pretty bullet proof. And I’m wondering if the 0starts means it isn’t picking them up but not sure. 
 

Binarydata Contributor

Binarydata

Posted
  • Author
Posted

I wouldn't think that the knock sensor would be causing a warm idle issue. Maf would. 

 

Mine comes up with 0 starts after resetting the ECU. If you turn the car all. Leave it for 5 minutes start it again does it come up with 1 start? 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • Dose Pipe Sutututu
      RB25DE NEO with Haltech ECU

      By Dose Pipe Sutututu · Posted

      post up screen shots of your injector tables
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • feartherb26
      RB25DE NEO with Haltech ECU

      By feartherb26 · Posted

      I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...