Jump to content
SAU Community

Recommended Posts

Hi all, 

I'm going to be selling my R32 GT-R early next year (Feb/Mar) in order to fund a house. I'm putting it up for sale now so I can hopefully have a buyer ready when I've completed some final work on it. The car is located in Perth but I'm willing to ship interstsate. Specs are listed below.

1992 R32 GT-R, 130,000kms on chassis, 6,000 on engine. 530 kW/710 hp @ 25psi on United E85.

Price: $52,000 O.N.O (no swaps please) - I can also arrange for registration for any NSW buyers interested.

Engine:

- R34 GTR bottom end, completely stripped
- Block acid dipped, cleaned, bored & honed
- R34 GTR crank (30,000 km) and rotating assembly balanced
- ACL Race bearings
- ARP main studs
- ARP head studs
- Nitto oil pump
- Ross forged pistons
- N1 water pump
- Ross 1000hp harmonic balancer
- Tomei cam gears in/ex
- Tomei Poncam 260 deg 9.15 lift in/ex
- R34 GTR head (30,000 km), refreshed with:
    - New valve stem seals
    - Bronze valve guides
    - Brian Crower dual springs
    - Brian Crower titanium retainers
- Tomei metal head gasket (1.3mm)
- Tomei oil pan baffle kit
- Autech catch can
- ARC grille oil cooler
- HKS fuel rail
- Splitfire coilpacks
- 6x Bosch 2200cc injectors
- AN-8 Teflon braided fuel line from external pump to rail
- Holley Dominator 1800 external fuel pump
- Walbro 460lph in tank fuel pump
- 3L surge tank
- Turbosmart FPR1200 fuel pressure regulator
- Koyorad radiator
- Nismo low temp thermostat
- TRUST 100mm drag intercooler
- 6boost T4 twinscroll exhaust manifold
- Precision 6870 Gen 2 turbo (1.00 twin scroll, v-band rear housing)
- Turbosmart Powergate 60mm
- Custom fab work for all intercooler piping (stainless steel), intake piping (K&N pod)
- Custom fab 4" dump pipe into 4" stainless steel exhaust (2x Magnaflow oval mufflers)
- Adaptronic ECU
- GReddy Profec OLED boost controller

Suspension/Brakes/Wheels:

- TEIN Super Street coilovers (5000km old)
- R34 GTR Brembos front & rear
- Project Mu 330mm front & rear
- Project Mu brake pads front & rear
- 18 x 9 +20 BBS LM wrapped in 6000km old Yokohama ADVAN AD08R tyres (265/35/18)
- HICAS locking bar

Driveline:

- Rebuilt R32 GTR standard gearbox (refreshed with OEM Nissan parts 6000km ago)
- Exedy twin plate clutch

Interior, Exterior & Accessories

- R33 GTR seats in front (older pic attached shows R34 seats, but they have been switched out for R33 ones)
- Nismo 320kph speedo from factory
- Momo steering wheel
- N1 headlights
- Genuine N1 3 piece sideskirts & rear spats
- Genuine N1 front bumper
- Full professional MNP1 respray.
- HKS Kansai Service strut tower bar (not pictured, but included)
- Rockford Fosgate speaker system front + back with Alpine single DIN head unit

As previously mentioned, I'm preparing some final modifications and work prior to sale, which includes:

- Fitting of a DEFI ZD OLED display as a readout for oil/water temp & pressure
- Fitting of a Platinum Racing Products R35 GTR coilpack kit
- Re-tune on 35 PSI boost (the car was previously running this boost with a precision 6466 Gen 2, making the same power as it does now with the 6870 on only 25 PSI)
- General clean up of body/full detail
- Addressing minor things like cosmetic wear (fading) on weatherstrips (seals and trims are generally in great condition)

The car is accident and rust free. I have some receipts for parts and work carried out on the car. The car does not have aircon installed, but I have the entire system, including the lines in perfect cosmetic and functional condition, which will be included in the sale.

Most maintenance has been carried out by myself (3000km intervals), using Penrite 10 tenths racing oil (10W-40). Redline shockproof oil in the gearbox.

You can contact me on:

Mobile: 0411 271 646 (prefer text, but can arrange calls after work hours)
Or PM me through here.

Cheers,

Nav

 

16107199_10154301860437358_7453806377926729462_o.jpg.f5e3e435f3ddb610c66124fd8300a575.jpg

20161212_174952_preview.jpeg

received_10154535558287358_preview.jpeg

received_10154409696642232_preview.jpeg

20170717_192454_preview.jpeg

PPSR Search Certificate 6885549857410001.pdf

received_10154643498467358_preview.jpeg

IMG-20161212-WA0007_preview.jpeg

Link to comment
https://www.sau.com.au/forums/topic/472839-700-hp-mnp-bnr32-1992/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...