Jump to content
SAU Community

Recommended Posts

Hey it’s so I was on my way to work this morning and on break I noticed mY break lights were on so I tried turning my lots off which they already were Off, I tried turning my car on and off same as my lights and it still didn’t turn off, I then checked to see if the pin was good and it was all goods can someone help how I can fix this ? Cheers 

Link to comment
https://www.sau.com.au/forums/topic/473052-brake-lights-won%E2%80%99t-turn-off/
Share on other sites

3 minutes ago, Ben C34 said:

What pin?

Normally the switch on the brake pedal causes it. Check out with a multi meter 

It’s the one that has the little rubber part on the end of it and a clip going through it but that’s fine, however I can’t seem to pull the switch out is there clips holding it in? 

The switch for the brake pedal just has a plastic nut holding it on from memory?

That will be your issue. I had the part that reacts on the switch fall off mine once so was an easy fix but sounds like yours might be the switch itself

2 hours ago, 89CAL said:

The switch for the brake pedal just has a plastic nut holding it on from memory?

That will be your issue. I had the part that reacts on the switch fall off mine once so was an easy fix but sounds like yours might be the switch itself

Yeah man that’s what I’ve narrowed it down to, just so such a tight fit to get too 

5 hours ago, 89CAL said:

The switch for the brake pedal just has a plastic nut holding it on from memory?

That will be your issue. I had the part that reacts on the switch fall off mine once so was an easy fix but sounds like yours might be the switch itself

I’ve found the problem it’s the little black stopper that has fallen off 

  • 2 months later...

This happened to me last night. Luckily looked in my garage before going to bed, pulled the fuse so it didn't drain the battery.

Attached images for others if it happens to you. (Part number suits a 95 R33 gtst)

Surprisingly cheap part from nissan spares. Taarks was slightly cheaper (but out of stock)

 

20180405_083536.jpg

20180405_100531.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...