Jump to content
SAU Community

Recommended Posts

Hey it’s so I was on my way to work this morning and on break I noticed mY break lights were on so I tried turning my lots off which they already were Off, I tried turning my car on and off same as my lights and it still didn’t turn off, I then checked to see if the pin was good and it was all goods can someone help how I can fix this ? Cheers 

Link to comment
https://www.sau.com.au/forums/topic/473052-brake-lights-won%E2%80%99t-turn-off/
Share on other sites

3 minutes ago, Ben C34 said:

What pin?

Normally the switch on the brake pedal causes it. Check out with a multi meter 

It’s the one that has the little rubber part on the end of it and a clip going through it but that’s fine, however I can’t seem to pull the switch out is there clips holding it in? 

The switch for the brake pedal just has a plastic nut holding it on from memory?

That will be your issue. I had the part that reacts on the switch fall off mine once so was an easy fix but sounds like yours might be the switch itself

2 hours ago, 89CAL said:

The switch for the brake pedal just has a plastic nut holding it on from memory?

That will be your issue. I had the part that reacts on the switch fall off mine once so was an easy fix but sounds like yours might be the switch itself

Yeah man that’s what I’ve narrowed it down to, just so such a tight fit to get too 

5 hours ago, 89CAL said:

The switch for the brake pedal just has a plastic nut holding it on from memory?

That will be your issue. I had the part that reacts on the switch fall off mine once so was an easy fix but sounds like yours might be the switch itself

I’ve found the problem it’s the little black stopper that has fallen off 

  • 2 months later...

This happened to me last night. Luckily looked in my garage before going to bed, pulled the fuse so it didn't drain the battery.

Attached images for others if it happens to you. (Part number suits a 95 R33 gtst)

Surprisingly cheap part from nissan spares. Taarks was slightly cheaper (but out of stock)

 

20180405_083536.jpg

20180405_100531.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
    • Yeah - I mean, go the other way. Smaller range. Not larger.
    • To re-cap, I bought: https://www.alibaba.com/product-detail/Lsailt-8G-Infiniti-Q50-Q60-2014_1601171829627.html?spm=a2756.trade-list-buyer.0.0.2cd476e9FTIlKE As you can see, if I bought 20 it was $653, but I bought 1 so it was $1,170. I was very tempted to buy 2 and resell 1 at 25% cheaper. @MBS206, I am not sure if they do a Kluger one, here is their list but it might be there under a global model name: http://www.lsailt.com/product/android-interface?page=1 Keep in mind these full android replacements have basically all the bits a phone does (cpu, ram, storage, wifi, bluetooth, usb interfaces) other than a screen (it uses a host), thus the $800+ cost. Android Auto screen mirroring is MUCH cheaper as it's just a cut down shell, input mirroring and output mirroring BTW I also need that "screen off" feature, it is much harder to see wildlife even if a dash is reasonably dark. Both the Fuga and V37 have display off buttons for night use, they just come back on for a second or 3 if you interact with it, eg skip a song.
×
×
  • Create New...