Jump to content
SAU Community

Recommended Posts

was looking at autobarn today and they sell these carpeted 6x9 speaker boxes that sit on your rear parcel tray.... sorta the same as a sub box but alot smaller....

they are around $70 a pair and im thinking i probably could make some cheaper then that....

would anyone have any measurmants and instructions on how to make a good style of box.... when sat in properly the speaker sorta angles up towards the roof a bit.....

any help/tips would be greatly appreciated.....

:(

Link to comment
https://www.sau.com.au/forums/topic/47686-6x9-speaker-boxes/
Share on other sites

  • 4 weeks later...

no point in low passing 6x9's if you have a sub...mine atm are running normal (no high/low pass) along with my sub, sounds pretty good. with my new splits up the front it sounds a hell of a lot better, but my rear speakers are nothing special.

i didnt know that 6x9's were made like subs, by that i mean to run in sealed/free air...can you port/bandpass them aswell for something different?

Link to comment
https://www.sau.com.au/forums/topic/47686-6x9-speaker-boxes/#findComment-991345
Share on other sites

  • 8 months later...

I'll say it again; the acoustic suspension of 'most' 6x9s is not designed to run in sealed enclosures. The result is that you will not attain optimum bass at best and you'll damage the speaker at worst. :P

On the flipside (once they're installed correctly) and for those of you doubting the bass output of 6x9s, remember the bottom (main) cone is 6x9". That is only marginally less surface area than an 8" subwoofer so they can thump quite hard..

I'll say it again; the acoustic suspension of 'most' 6x9s is not designed to run in sealed enclosures. The result is that you will not attain optimum bass at best and you'll damage the speaker at worst. :(

On the flipside (once they're installed correctly) and for those of you doubting the bass output of 6x9s, remember the bottom (main) cone is 6x9". That is only marginally less surface area than an 8" subwoofer so they can thump quite hard..

Yea my first system i had 6X9's amped in the rear parcell shelf with the low pass filter and running around 50hz at the time and they produced some pretty good bass for speakers that were $100. But you can't go past a sub for convential bass and its a lot tighter, easier to tune and better quality sound is my 2cents. Good set of splits tuned right and a sub in the rear, no real need for rear speakers is there. The sound of them is shooting up and from behind you, your ears face forward when your in the car (unless there is something we dont all know about :wassup: ) so unless you were to fade them to the front more and just run them as a high pass i can't really see the need for them.

But in saying that you do what suits you and what you like the sound of, its your system and thats what counts at the end of the day. :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
    • Do you have some data like fuel pressure? It's really hard to say if you're still fighting a fuel system issue at this point. Could be something weird like the FPCM dipping out.
    • Yeah in that case, pulling the dent out. Event a very slight dent can create a lot of work filler-wise and there is a strong chance the panel won't be the factory shape when you are done (as the dent will result in a new high point created somewhere, then everything is brought up to that new high point... but the panel shouldn't be that high if that makes sense).  So you've filled and primed the panel and it is flat, why would you go back and remove the primer and add more filler? 
    • Something else I have been faffing with while the car was off the road is making the AC work. Assuming the car isn't at a thermal limit the idea of having AC while waiting in line to go on track sounds delightful. I have actually been lugging around the weight of the entire system since 2018 when the RB25NEO went in without it working at all.  The main reason was in the first few events before I got around to re-gassing it the rubber hose that runs under the manifold had the factory heat wrap/sleeve fail resulting in this: ~2 years ago I purchased a complete used R32 AC line set but when I finally went to install it the line i needed was different where the expansion section is I found a local place that was able to replace the rubber section and re-crimp. They also added some modern heat sleeve to the hose Tight fit but fingers crossed this is the last physical piece of the puzzle needed
    • the top black section is bonded to the silver section with some form of rubber. I assume to isolated NVH from the box
×
×
  • Create New...