Jump to content
SAU Community

Recommended Posts

Own a skyline R34 1998 coupe.

After my car died I tried to jumpstart it, I had the cables on the wrong way and I think it fried something. Right now my AC, central locking and radio unit isn't working. I'm hoping it's a fuse problem but worse case probably not.

My passenger side right now will not lock, both when I try to lock it from the inside and outside.

The lock seems to be jammed or something because when I push it in, I always pushes back out and unlocks it self. Same goes for when I use the key outside the door to lock it. It always forces itself to unlock. Any ideas on what the problem is.

Is there a fuse that might control the lock? I don't think the actuators are the problems because it can push it self out so I'm thinking it might be getting a current that constantly forces it open.

 

Link to comment
https://www.sau.com.au/forums/topic/480031-passenger-door-unable-to-lock/
Share on other sites

Disconnect the battery again and see if you can lock it with the key. That will tell you if it is doing it with power of with a "spring". If it is lockable without power, then don't leave the battery connected, or you will likely drain it or maybe even burn something.

Go check all the fuses. Both under the dash and under the bonnet. Find any that are blown and replace, then consider what works and what doesn't work.

Be prepared to take it to an auto-elecctrician, because you have a number of other systems in the car (the ECU, the ABS/TC CU, the HICAS CU) that could all be grumpy with you for smashing the electrons in backwards. They don't usually take kindly to the nasty transient voltage spikes you get when you make and break backwards battery connections.

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
×
×
  • Create New...