Jump to content
SAU Community

Recommended Posts

Well thanks to COVID we had a slight change to dates but we are locked in an ready to go

1311447506_IMG_1418(1).thumb.JPG.d4f72bfbaaa5d91c9d1716a6a96354f9.JPG
 Entries now live

If you have never done a motorsport event here is your chance.

We wanted to hold a skidpan day whereby members could get a massive discount, the day is designed for someone who has never done a motorkhana or a track day up to advanced.

When: Saturday 31st July 2021

Where: Winton Skid Pan (Winton Motor Raceway)

Price: $50 for SAU VIC Members ( will need to present membership card on the day)
           $99 for non Members
Entries: Limited to 26 cars

What you need:
Valid Motorsport Australia L2S Licence or AASA Day licence ($35.00 via the AASA Website)
Running car that does no leak fluids everywhere
Long sleeve top and pants
Helmet that meets Australian Standards
A fire extinguisher that is within 3 years of manufacture and in the green.

Accommodation:   We have reserved room at the following motel for the Friday and Saturday night. ( Can book one or two nights)

There is parking for trailers next to the motel.
To book your room reservation is under Leon. If you decide to stay somewhere else just let us know so we can invite you to dinner etc.
 
Glider City Motel
2 Witt St, Benalla VIC 3672
Phone : (03) 5762 3399   There are some rooms reserved under "Leon"

Entry link: https://www.sauvic.com.au/entry/deca/20210731

Bring your car and get to battle others, win loose or draw I can guarantee you will have lots of fun.

Any questions email [email protected]

Entry List:

1. Warren Clark
2. Tony Buckland
3. Simon Henman
4. Annabel Schulze
5. Luke Schulze
6. Josh Miller
7. Ben Simons
8. Leon Stapley
9. Gregory Wise
10. Krystal Pfeiffer
11. Joselito Da Rocha
12. Tegan Collins
13. Jeremy Blackman
14. Sean Power
15. Haydn Wilde
16. Peter Blythe
17. Chris Lack
18. David Heskin
19. Travis Pfeiffer
20. John Beck
21. Samuel Thompson
22. Tim Watson
23. Jason Carey
24. Adam Mooy
25. Andrew Collins
26. Aaron Klaver

Reserve list:
27. Ryan Bell
28.



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...