Jump to content
SAU Community

Recommended Posts

Hello all,

I've just bought myself a previously modified/tuned 1996 Skyline r33 GTS-T and I'm already loving this car. I come from the Subaru WRX world so my knowlege on these engines is nonexistent. However, I've been told this forum is *the* place to go for information on these cars.

Good news is I already have a tuner (the same tuner who originally tuned this car a few years ago) and at least a general idea of how turbo cars work, haha.

First thing I want to do it change all the fluids and filters. I'm searching these forums and online, but looks like Mahle Knecht or Mann are both good oil filters and Im happy to see Motul be highly recommended for oil as that was my goto with the Subaru. It looks like 10w-30 is a safe bet, but I see other suggestions floating around too so Im not sure what weight to go with.

I figure I cant go wrong with genuine Nissan coolant. The transmission fluid was changed a year and a half ago, but I'd feel better swapping it out and same with a full brake fluid flush likely motul on both if available.

She def needs some work. Some boot rust to tackle before it gets bad, some weird clunking probably from the suspension, and some mystery switches that I think mess with the turbo or tune.

Any other advice or "check this" or "make sure this is good" before I get too deep into this car is appreciated. She is going to the tuner first thing this week for a full checkup.

 

20221223_155846.jpg

signal-2022-12-23-20-02-42-976.jpg

 

20221224_161748.jpg

20221224_161812.jpg

Edited by IXMandalorianXI
  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/484300-hello-from-the-uk-new-to-nissan/
Share on other sites

Welcome to the forum,

Looks like a very tidy car. Good idea on doing all the maintenance from the start. Clinking will be subframe or diff bushes or both best to just do every bush at once with a Whiteline rubber kit, stay away from the nolathane stuff.

Oil choice is always different pending climate, always good to use a quality oil. I run a 15-50 but its a lot warmer here and on ethanol.

They can be a solid car when looked after buy its a rabbit hole once you start modifying them.

Thank you for the reply and information! The car has been well take care of best I can tell. Only 52,000 miles, a fresh paint job and receipts and paper trails for a lot of mods and inspection passes.

Could you elaborate on "subframe clinking?" That sounds rather worrisome. Bushings less so and makes sense. Whiteline is a company I know well and will def look at their kit. Thank you.

It looks like the last owner used Fuchs Titan Race Pro R 15W-50 full Synthetic. The UK can be really cold or really warm. I figured an all season oil would be a safe bet.

The car seems pretty much full bolt on plus an upgraded turbo, clutch, coilpacks, coilovers, all tuned on a G4+. Seems to have been done properly. It really was a unique find. Last owner had to trade in for a family car Ive been told. Not much I want to mod beside quality of life, mostly maintain and restoration.

Edited by IXMandalorianXI
1 hour ago, IXMandalorianXI said:

Oh, after some googling and rereading, you meant subframe bushing, not that the subframe itself was making noises. That makes more sense.

 

If you try hard enough on the track over enough years, you can crack the subframe too lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...