Jump to content
SAU Community

Is this rb26 block useable for modest build?

hixzoomy
 Share

Recommended Posts

hixzoomy Apprentice

hixzoomy

Posted
Posted

Hey Sau,

Long time lurker. I just wanted some opinions from the experienced guys to see if this block is still useable or if it's a boat anchor and I should try get my money back? My concern is this crack between the water jackets to the head bolt thread between cylinder 3 and 4 see picture attached. Little back story about it, I bought it as the start of a small build to put into my daily. Was told was running fine no issues the previous owner had just pulled it down to go forged bottom end lost motivation and was now selling if off, after I started to clean it up I found the crack. The target I'm aiming for would be between 375 - 450kw so not the biggest power output but as it's going into my daily ( probably in the year 2050 at this rate) I'd like to give it a chance at surviving for as long as possible. 

crack in deck rb26.PNG

GTSBoy Grand Master

GTSBoy

Posted
Posted

As far as I know the spot that breaks most commonly is on the exhaust side, adjacent to #4 or between 4/5. So any unnecessary weakness on the exhaust side, even if it's not is the "usual" spot, can't be a good thing. And between 3 & 4 is not so far away from where the block likes to jump to pieces.

hixzoomy Apprentice

hixzoomy

Posted
  • Author
Posted

Thanks for replying so quickly and sharing your knowledge. I had heard of the block issues between cylinder 3 and 4 splitting and the crack on the outside of the block from block twist after a healthy amount of power put through them but this is all new to me. When I spotted it I thought it might be a drama but was hoping it was more superficial so I could finish making the deck flat give it a hone and get down to ordering some parts, looks like I might have to start getting in touch with the seller to try get my cash back. 

BrynDETT Community Regular

BrynDETT

Posted
Posted (edited)

Mine has a crack from water gallery to headstud hole in-between 5&6... Sent it back together, been a year so far at 520kw and had no dramas yet .. I guess it all depends if you are prepared to do all that work to potentially do it all again 🤣

Edited by BrynDETT
  • Like 1
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...