Jump to content
SAU Community

Recommended Posts

Currently looking into available exhaust options for the Skyline Coupes CKV36.

Was wondering what people run, as our cars aren't heavily supported in AUS.

Well aware that you can run 370Z exhausts on our car with an extension pipe but my import has the 4WAS module stuck to the back of the diff making it incompatible with most available G37/370Z exhausts (HKS, Motordyne, ARK, etc). The 370Z exhaust all bend inwards towards the back of the diff before straightening out making it incompatible. 

 

image.thumb.jpeg.24a3d626e7ea500f071dec3cbbeb43a4.jpegimage.thumb.jpeg.39ff19038d7a695a952e6a5009ac7994.jpeg

 

I was initially looking at Tomei for the weight savings but it hangs way too low for it to be driveable + do not want to be a police magnet. (NSW Limit 90dB -> Tomei 112dB)

 

image.thumb.jpeg.59933489998f936e81814ef21bd018d3.jpeg

 

Bit of a reach but if anyone here has a Skyline Coupe CKV36 with a 4WAS module, what exhaust setup are you running?

Link to comment
https://www.sau.com.au/forums/topic/484686-ckv36-exhaust-options/
Share on other sites

Yes, all custom built by myself. no idea on the cost, was all part of a larger build. Was quite a few years ago too, so materials are probably friggin double now.

No idea of your situation, but the cheapest way imo would be to get what you want in 370z fitment & then pay someone to mod it to fit properly. Would be way cheaper than building from scratch. Decent exhaust work isn't cheap. Just make sure they're not a "Press Bends & Mig" shop.

If you decide to go full custom, following my layout may help save some dough, go to my build thread & it leads to my youtube channel. I documented the full exhaust build there.

Cheers.

  • Like 2
6 hours ago, Duncan said:

Custom is probably quickest and cheapest for pretty much any JDM unless you stumble across some ebay junk

Noted :)

 

5 hours ago, mycarhasposessedme said:

Yes, all custom built by myself. no idea on the cost, was all part of a larger build. Was quite a few years ago too, so materials are probably friggin double now.

No idea of your situation, but the cheapest way imo would be to get what you want in 370z fitment & then pay someone to mod it to fit properly. Would be way cheaper than building from scratch. Decent exhaust work isn't cheap. Just make sure they're not a "Press Bends & Mig" shop.

If you decide to go full custom, following my layout may help save some dough, go to my build thread & it leads to my youtube channel. I documented the full exhaust build there.

Cheers.

The exhaust setup looks amazing!

Thanks for the information, appreciate the help :) 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...