Jump to content
SAU Community

Recommended Posts

Originally pulled from an automatic Stagea.
Has flex fuel kit / feature pack installed + comes with consult cable. Running base map to suit stock setup.

Connector could do with a squirt of contact cleaner, but had zero issues other than tuners being reluctant to touch such ancient technology. :P

$350 posted.

PXL_20230806_015709179.thumb.jpg.71ce789e1ddbe9645784a7639ebaea82.jpgPXL_20230806_015647556.thumb.jpg.6f70366685187b687e8b1fffa00c94b6.jpg

 

Link to comment
https://www.sau.com.au/forums/topic/484838-nistune-ecu-to-suit-rb25det-neo/
Share on other sites

Nah, just the ECU itself.
Swapped it out for a Link unit a while back and has just bit sitting in the parts pile since.
Finally had a purge and binned most of it. Figure this would still be of use to someone, somewhere.

1 hour ago, Wazmond said:

Now im not too sure, but wouldnt there be an issue if you were to chuck that in another c34 stagea auto

Wotcha mean? Take an ECU out of one car and put it into another near identical car and....problem?

Has the base tune loaded, so if you're using stock injectors/maf etc. It will just run as is. If not, it'll obviously need to be tuned to suit.

Was running the neo in my manual R32 until recently.

  • 5 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
    • Sounds good, we will aim to be there! @The Bogan I'll give you a shout if you are heading up to campbelltown for the meet too.
    • Before I get to the test day, just to finish off the android head unit. This is a demo from car start up....the standard/host system takes a few seconds to boot (same as all v37) but Android comes up quickly. In this vid I'm using the delivered launcher but have set the default to Agami since which is easier to navigate when if use primarily 5 apps. You can see the host system still takes over when required eg putting it in reverse, and you can switch between Android and not by holding the back button 3 sec. It is pretty responsive (fast) but you can see I had to press harder than expected a couple of times.  I still have the phone connected to the stock system, and that also seamlessly takes over Android music playing. v37-android-demo.mp4 The bigger reason that I put this in though is so that I can use Ecutek directly on the head unit. That gives me a dash with logging (up to 20MB only), high and low value warnings on any parameter etc etc. I've run a USB cable from the Ecutek OBD dongle to a USB input on the unit, easy. v37-ecutek-demo.mp4   The unit did freeze on the launcher the other day, I think Agami was trying to verify the license when it didn't have a data connection...will monitor and report back if there are any other problems but so far I'm very happy with the upgrade.
    • Nah that is just crappy GPS mapping, I did have a small excursion (cold tyres, damp track, surprise!), will post up that when I get a chance.
×
×
  • Create New...