Jump to content
SAU Community

Recommended Posts

Hi guys,

Driving along today, my engine light flicked on showing code 14 speed sensor circuit.

It came on when i was cruising in 5th at 70kmh. No noticeable change in the driving experience, no slip light or anything else. Speedo works fine, the only thing that's different is my bulb in the bottom left of the dash has gone.

So I know this is going to be a dumb question but the bulb couldn't possibly be throwing this code? Otherwise I have no clue where to start, apparently this code could be anything along the speed sensing circuit? So speed sensor and wiring back to the ECU etc.

Is there a way to test the speed sensor to see if it's faulty?

If anyone is able to point me in the right direction to start would appreciate it. Cheers

Screenshot_20240521-171551.png

1 hour ago, Annex said:

Hi guys,

Driving along today, my engine light flicked on showing code 14 speed sensor circuit.

It came on when i was cruising in 5th at 70kmh. No noticeable change in the driving experience, no slip light or anything else. Speedo works fine, the only thing that's different is my bulb in the bottom left of the dash has gone.

So I know this is going to be a dumb question but the bulb couldn't possibly be throwing this code? Otherwise I have no clue where to start, apparently this code could be anything along the speed sensing circuit? So speed sensor and wiring back to the ECU etc.

Is there a way to test the speed sensor to see if it's faulty?

If anyone is able to point me in the right direction to start would appreciate it. Cheers

Screenshot_20240521-171551.png

Most likely if the speedo works fine it's the driver circuit in the cluster that takes the VSS signal and converts it into a neater format for the ECU/HICAS/etc. Pull your gauge cluster out and clean the board with contact cleaner, all that fun stuff. Look for corrosion, signs of burned contacts, failed solder joints, etc.

You won't likely find an R34 manual, but the R33 (and probably usefully enough R32, if you know how to infer) manual will tell you how to inspect the speed signal. You will need either consult or an oscilloscope. Now is the time to buy a cheapy scope from aliexpress if you haven't got one. No-one should be without one these days.

19 hours ago, joshuaho96 said:

Most likely if the speedo works fine it's the driver circuit in the cluster that takes the VSS signal and converts it into a neater format for the ECU/HICAS/etc. Pull your gauge cluster out and clean the board with contact cleaner, all that fun stuff. Look for corrosion, signs of burned contacts, failed solder joints, etc.

Thanks mate, honestly would make sense, I reflowed my gauge cluster solder joints last week after that wasn't working. now it works like a charm 

15 hours ago, GTSBoy said:

You won't likely find an R34 manual, but the R33 (and probably usefully enough R32, if you know how to infer) manual will tell you how to inspect the speed signal. You will need either consult or an oscilloscope. Now is the time to buy a cheapy scope from aliexpress if you haven't got one. No-one should be without one these days.

I've been looking for an excuse to buy an oscilloscope off ali express. My time is now! Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Will have a look at that. I cant see any leaks 
    • Put another overflow bottle (ie, a 1.25 coke bottle or similar) under the overflow hose and see if it is being pushed out there or if it is disappearing into the engine.
    • Staring on a stand is no issue. You just have to wire everything up, give it fuel and cross your fingers that the stand is robust enough. Arranging the inlet plumbing is often the hardest part, without any surrounding structure to hand some of it from. No need for coolant if you only want to run it for <1 minute. As to the gearbox - I think the little Aisin box is a bit stronger than the other small Nissan boxes that went behind SRs, but I wouldn't be too keen to test its limits with the torque of a boosted 25. I don't know if you can retain the box and the tailshaft. The box won't connect to the RB without an adapter of some sort, which is either a plate that will push the engine forward (which is not good for fitting it into the bay's available space) or push the box back, which messes with the box position and tailshaft length - OR - cut and shut work on the bellhousing, which is a long way from "least modification". I'd be buying a new 370Z 6 speed or similar, doing what has to be done to that to make it fit RB (ie, cut and shut bellhousing) and the requisite tailshaft custom/mods.
    • Hi Everyone I am from West Pennant Hills in NSW. Been too busy until recently to attend to my RB25DET Series 2 engine until recently. I am planning to stick it into the S15 shell at this stage, unless a nice SR20DET turns up... For now, i am going to try and get the RB25 running and working well then decide what gearbox to use. My preference is to retain the SR20DET  6 speed gearbox and tail shaft to retain as much and least modifications as i can avoid. I am an old guy and won't be doing any heavy drifting so i don't need a bullet proof gearbox Does anyone have experience with starting the RB on a stand? I got everything setup as much as I can with the info i can find... endless searching and videos on Youtube I would be great to get some pointers Cheers Songo
    • Hey all, Recently have had my s1 r33 gtr serviced and noticed my coolant reservoir was topped up to the max line. Took the car out for 1 yesterday and noticed today the reservoir is completely empty.  Any ideas? Radiator is full
×
×
  • Create New...