Jump to content
SAU Community

Recommended Posts

gentlemen (and others)...

at 157k km on my rB25DE auto sedan and am getting an every-so-often A/T light, with the usual loss of whatever gear i'm in at the time. it always goes away once i restart, but i read the threads and watched every video and am told it will only get worse.

i have zero evidence anyone has ever done a trans flush on this car.

is there a chance that doing a flush will fix the problem, rather than the usual "replace the A/B solenoids"? just curious. rather not flush, seal it up again, then have to drop the pan all over again...

EWlQNeY.jpeg

 

5 minutes ago, GTSBoy said:

Get a scan tool on the Consult port and see what the TCU has to say for itself.

was my first thought, but a couple hundred for the cable/adapter plus not having a laptop that can run NIstune/NDSI/ECUtalk or any of the usual programs is the issue.

honestly i'm going to flush it anyways and so i guess this is a little like asking people to internet-diagnose my car. 

just wanted to see if anyone's ever had an A/T light go away purely by doing this though

On 10/28/2024 at 6:37 PM, GTSBoy said:

Just go to a quality workshop that has a quality scan tool and ask to plug it in for a few minutes. Throw them a six pack.

Nobody around me has a Consult (USA east coast) :( 

Either way I ordered all the parts to do a trans flush so guess I'll do it anyways.

4 hours ago, thatjawncrazy said:

Nobody around me has a Consult (USA east coast)

It's just not true. It does not have to be a "Consult". Professional grade scan tools from EVERY major workshop equipment electronics manufacturer will happily interrogate Nissan electronics. Things like Snap-On scan tools, etc. That is what they are for. This is why I said...

On 10/29/2024 at 9:07 AM, GTSBoy said:

Just go to a quality workshop that has a quality scan tool

 

On 11/1/2024 at 5:38 PM, GTSBoy said:

It's just not true. It does not have to be a "Consult". Professional grade scan tools from EVERY major workshop equipment electronics manufacturer will happily interrogate Nissan electronics. Things like Snap-On scan tools, etc. That is what they are for. This is why I said...

 

if I find a shop that has an OBD I tool and can connect it to the port - i wonder what the suggested route is for purposely triggering transmission limp mode while i happen to be within driving distance of the shop, and then dropping everything to stop by and have them scan it. so, it would be nice if things worked out that way - but in case they don't, we are back to my original question of "will bad fluid ever trigger limp mode on its own".

  • 1 month later...

interestingly enough, i found out the answer is yes. doing a flush did fix my recurring A/T light. it might have been because of the trans filter:

QyJqGs3.jpeg

but that doesn't really make sense to me. the fluid/filter was super dirty. would that increase the pressure in the lines and trigger an A/T light? does the car even have a way of detecting that? i have no idea. i've done 200+ miles after the flush and no A/T light. if my A/B solenoids went bad, i would think the light would've come on.

shifts and drives way better now though...at 2k rpm instead of 2500...no hesitation and downshifts when i want it to. 

wBfUdgK.jpeg

  • Like 1

Well, if that filter was impeding fluid flow, then it could have similar effects to faulty solenoids. The TCU will register a fault when it does something (ie, changes the state of a solenoid) and does not detect the required result. If there are other causes that can make the same lack of result, then they will be indistinguishable to the expected cause for which the TCU has a code.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...