Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...
  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

Atmos were 4.11's, Turbos - 3.90. At least in the DR-family.....

OK, looks like it could be the same for HRs too. Mine was L20E from factory according to manufacturer plate, but had the L20ET when I bought it.

and... i've got an original HR30 with L20t (l20a) and tho it's ok (not really).. i'd love to put a L24/L28 into it!!... why?.. cause every other wanker has a RB!! b different go old skool!!! REMEMBER most of the people that will see it are too young to understand the raw power (?) of a L series revving off it's nut!! Hell put a VH45 into tha sucker!! if i could find a good 240K coupe in perth Thats what i'd do!! bugger ya all i'm going to bed!

really in the long term the compression still would be to high, which would make tunning impossible. the best option is to take the L28 and chuck the LD crank. and so forth.

The LD28 with l20 turbo intake manifold runners are to long which is good for low down torque but stangles the top end so that manifold would not be adiqit. the l28 one would work much better.

The l20et exhasut manifold is the same accross all L turbo motors, even for the astranged l24et motor. It is listed on nissan's system. :rofl:

Given the cost and rarity of good L28E blocks, has anyone thought of using an L28D bottom end with a de-compression plate and L20ET head, manifolds etc. etc. The bottom end would be indestructible given that its made to handle 23?:1 compression ratio.

 

 machg

I respectfully disagree,

The L28 was available in at least 3 different models in Australia - 280ZX, 280C & the Patrol. The LD28 was not released on the Australian market at all.

The LD28 block is also a mid-height block (same as L20b), which could make fitting an issue. the L20A/24/26/28 & L13/14/16/18 are all 'short' blocks, while some of the Z blocks are taller again.

A mildly-prepped L28ET (custom, or factory) will turn 300HP on standard internals with good tuning. The LD28-crank option is a bit of a mixed blessing. It gives you the potential to go out to nearly 3.2L, with lots of low-down torque, and a healthy power output. But this is at the expense of rod/stroke ratio and total rpms. Balancing is also critical on a stroker.

Ideally you need to use L14 rods (which are longer than L24) and a very short skirt piston in order to make the best of the combination.

I considered buiding my twin-turbo L28 as a 3L stroker, but have decided that block rigidity & ease of construction were more important than an extra 200cc's. My LD28 crank will therefore stay in the shed...

I've also considered building a very over-square engine by mating an L20A crank to an L28 bottom end. I'm sure I could crack 10,000rpm if I tried hard enough!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...