Jump to content
SAU Community

3.1 L Stroker

Ghostrider
 Share

Recommended Posts

Ghostrider Grand Master

Ghostrider

Posted
  • Author
Posted
Are you talking about using the diesel L series crank?

If so, I know a guy through a friend who's done it before. I can try and get you his details if you want.

That's right! The top package is F54 L28ET Block, LD28 Crank, Z24 Pistons, N42 Head etc, etc gives a 3098 monster L Series.

Your friends contacts would be cool.

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/49229-31-l-stroker/#findComment-985651
Share on other sites
  • 4 weeks later...
cronk Rookie

cronk

Posted
Posted
Has anyone attempted to build the 3.1L L Series Stroker engine in Australia?

Just wondering if you know how a N/A l28 would cope if I bolted the turbo set up off my l20et onto it ? Would i need to lower the compression ratio as i have seen a few posts saying just bolt it on and go for it . Any info would be appreciated .thanks :cheers:

Link to comment
https://www.sau.com.au/forums/topic/49229-31-l-stroker/#findComment-1011189
Share on other sites
72GT Enthusiast

72GT

Posted
Posted

Hey Chaps,

Can anyone tell me the difference in stroke between the stock L28 and the stroke when the diesel crank is fitted please?. I have what is alleged to be a Kakimoto 3.1 litre, and I figure if the difference in stroke is substancial, (measurable!) I should be able to tell using the "through the plug 'ole" method. As the motor is quite fresh and purring, I don't want to disturb too much!

Cheers,

Jim.

Link to comment
https://www.sau.com.au/forums/topic/49229-31-l-stroker/#findComment-1014902
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
×
×
  • Create New...