Jump to content
SAU Community

Recommended Posts

Just a quick question.

What does everyone think about Continental tyres.

I need tyres and im thinking of getting some.

:D  :burnout:

you might want to try the tyres forum, they are discussed there and seem to get a good mention from SkylineGeoff. Hankook Ventus K104 are also rated well for the price in another thread.

Link to comment
https://www.sau.com.au/forums/topic/49967-continental-tyres/#findComment-995124
Share on other sites

Well another shameless free plug for Ed, he has a tyre guy in Bathurst who brings him tyres every Tuesday. I got something off him called Maxus (I think?) which ive since been told are a rebadged Yokohama tyre. I was a bit sketchy at first, but have them on my car now, and am *VERY* impressed. In the wet if I used to accelerate hard, my rear wheels would start spinning (even when the front started pjulling) and wouldnt go anywhere. With these ones she just took off in the wet (and I also scared the shit out of my passanger :().

They were $300 for 255/40/17's and yeah, very impressed.

Link to comment
https://www.sau.com.au/forums/topic/49967-continental-tyres/#findComment-995385
Share on other sites

i'd say $300 each Andrew.

However, if they are $300 for all four, put me down 5 sets :(

SkyGTRline, i'd recommend you drive up to sydney to buy tyres, the money you'd spend on petrol would be much less than the money you save on buying and fitting them up there. or at the least, have them sent from sydney and installed down here.

the price some places in canberra charge for tyres is daylight robbery.

Link to comment
https://www.sau.com.au/forums/topic/49967-continental-tyres/#findComment-995455
Share on other sites

yea.. thanx guys...

Im just after second hand ones, Im planning on getting rims soon, so i dont really want to spend heaps on new ones..

When i bought the car the guys put second hand ones on the rear (Continentals) there was heaps of tyre, and they were bloody awsome... so i wouldnt mind getting some just for now.

The guys said like $100 each. so cheap, but just for now

Link to comment
https://www.sau.com.au/forums/topic/49967-continental-tyres/#findComment-995640
Share on other sites

i'd say $300 each Andrew.  

However, if they are $300 for all four, put me down 5 sets :D

SkyGTRline, i'd recommend you drive up to sydney to buy tyres, the money you'd spend on petrol would be much less than the money you save on buying and fitting them up there.  or at the least, have them sent from sydney and installed down here.

the price some places in canberra charge for tyres is daylight robbery.

Couldn't agree more, I went to St George tyre service and saved about $400/4 tyres compared to what I could get here. A word of warning though, other distributors hate places like them and Tempe etc, if you have a problem like I did - one tyre out of round - local distributors won't touch you as they maintain these tyres are parallel imports etc. It's still worth it in my opinion, just exercise some caution.

Link to comment
https://www.sau.com.au/forums/topic/49967-continental-tyres/#findComment-996648
Share on other sites

firstly what are continental tyres?

Continental are a Euro brand, they are quite widely used over there and can be found on some top-end models. They also make motorbike tyres.

Not to be confused with Continental Cup a Soup. Then again if you smell chicken noodle after a burn out...

Link to comment
https://www.sau.com.au/forums/topic/49967-continental-tyres/#findComment-996663
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...