Jump to content
SAU Community

Recommended Posts

still have a miss in my r33 under load at 5000rpm at 10psi.

have changed the spark plugs.

had it on the dyno with a fuel pressure guage( pressure good flow low)

replaced the fuel pump(nippon denso high pressure 400hp pump)

im going to clean the coil contacts where they go onto the spark plugs and ill check the little springs in the end of the coils.

want to know if anyones heard of boost cuts being as low as 10psi?

or maybe a boost sensor on the motor thinking it is over boosting?

the knock sensor might be sensing pinging at this certain rev? (havent heard any pinging)

any ideas let me know.

Link to comment
https://www.sau.com.au/forums/topic/50073-same-problem/
Share on other sites

when u changed ur plugs did u set a correct gap? .8mm is the general consensus here. what plug heat range did u use?

also do you have aftermarket ecu? stock ecu will sense boost increase and kicks in boost cut, can be as low as 10psi especially on cold nights. pfc will definitely fix that, otherwise a cheaper safc can do the job well if tuned properly.

Link to comment
https://www.sau.com.au/forums/topic/50073-same-problem/#findComment-996382
Share on other sites

hm.. hard to tell. cutting boost wire may not bring u anywhere as the ecu will need afm input, otherwise it'll go to limp-home mode and stutters at 2000rpm (found out abt this when my one of my afm wire was accidentally snagged).

i think could be something else causing it to miss. hopefully not a serious issue. can be quite a bitch to track down. i had similar issue in my car for over a year when it turned out to be fuel pump dying. had it replaced and all is sweet.

oh i just remember, what boost controller u use to run 10psi? dun trust any simple cheap bleed valve, it may spike, especially on higher gear. ask ur tuner to check it on dyno. best boost controller are always the electronic ones.

Link to comment
https://www.sau.com.au/forums/topic/50073-same-problem/#findComment-996443
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can u check this way it works for power supply?
    • These coils draw 10amps that what i read online
    • I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
    • That worked out PERFECTLY! Thank you big time to JJ. He was able to swap me his stock diff. He drove all the way to me as well. Killer! Removal & install was pretty straightforward. The diff itself is HEAVY. So that’s a 2 man job.  Man does the car drive nice now! Couldn’t have worked out any better 👌
×
×
  • Create New...