Jump to content
SAU Community

Drift Day - Eastern Creek - Sunday 19/09/04

boxheadmr

By boxheadmr,
in Events Archive

 Share

Recommended Posts

boxheadmr Mentor

boxheadmr

Posted
Posted

Initial Drift Australia will be holding a drift event at Eastern Creek on Sunday, 19th of September, 2004. The event will be held on the Eastern Creek Skid Circuit, a concrete low friction surface.

We will be running 2 sessions. The first in the morning will run from 9am to 1pm on a wet track. This is a perfect opportunity for those wanting to "give it a go" to get out there. The second session, run from 1pm-5pm will be on a dry circuit.

You may register for either one or both of the sessions. Should you only wish to participate in one session (either wet or dry) the cost will be $60 to members and $75 to non members.

Special Requirements

As a member of CAMS, Initial Drift will be requiring that all drivers and passengers wear long sleeve shirts and pants covering ankles to wrists to neck. Appropriate footwear must be worn along with a CAMS approved helmet (any AS helmet will do).

These requirements are not open for interpretation and are ultimately for your safety (http://www.initialdrift.com.au/forums/view...php?p=6608#6608). Please ensure that you bring the necisarry gear as you WILL NOT be running without it.

CAMS Licensing

For insurance reasons all drivers must hold a current CAMS license. Should you not have a current or valid CAMS license, that is OK. Initial Drift will be issueing daily licenses for $20.

Passengers will need to purchase a Passenger Licence and this can be had for $30.

To regester or find out more information please visit

www.initialdrift.com.au

0HR-30T Rising Star

0HR-30T

Posted
Posted
no you're not, you're doing a hillclimb in bulladelah....how about 10 October instead?

Would I be able to get some start times,info,etc for this event by any chance?

and I assume it's on the 19th of this month?

I've been wanting to go and watch one of these for ages,and have a mate in Taree who *may* be interested in competing.

:cheers:

0HR-30T Rising Star

0HR-30T

Posted
Posted
you'll have to be a member of a CAMS affiliated car club to enter it...

if you are, drop me a PM and I can send you the regs and entry form

Well I was just going to watch :Oops: Don't think my mate's a CAMS affiliated club member :cheers: Out of interest,would a CAMS Basic (white) licence be enough,or is that only for motorkahana's,etc? I suspect you need the next one up,for closed road competition(?)

  • 2 weeks later...
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Manur33
      Rb25det coil loom wire identification

      By Manur33 · Posted

      Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • davemoto63
      Stagea choice's which model??

      By davemoto63 · Posted

      Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • davemoto63
      Noobie Stagea owner..

      By davemoto63 · Posted

      Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...