Jump to content
SAU Community

Recommended Posts

Hey everyone,

My car just started this weird idle problem where it hunts up to 1.5krpm then drops back to 1krpm and so on, normal driving is fine just when I stop at the lights etc. it idles really bad.

The car was driving fine Saturday night but when I started it Sunday, after the cold start came off it did this weird hunting thing.

When the AC kicks it the idle stabilises at around 1krpm, but when it goes off it starts hunting again.

I have tried:

-adjusting the idle screw

-tightening the BOV (GFB hybrid)

-checking all hoses to make sure they are connected.

I have a PFC, could some setting on this be the problem, although it has been working fine previously.

It has done this once before on a skid pan, but all I did was turn the car off and on and it fixed itself?

I am quickly approaching the zone of confusion.......................

Link to comment
https://www.sau.com.au/forums/topic/50418-wiered-idle-problem/
Share on other sites

If you've got an R33 especially, it's your charcoal filter. This is a very common problem and you don't have to worry about it much. Depending on the conditions it'll have its goood days and bad days. If you really wwant to reposition your charcoal filter, you'll have to use up a fair bit of money.

make sure your dipstick is in properley, and inspect your oil filler cap seal!!! (just check them, it can't hurt!!) Mine (R33) stalls when I remove either one of the 2 when warmed up and idling.

The charcoal filter is a filter for the air conditioning. It just simply filters the air so it is pure. However, it can end up slightly changing the idling of the car. It's nothing to worry about. I have the same problem on my R33, but it's severity varies.

Are you sure about this?

As i thought the charcoal filter is used to filter out petrol vapour from the fuel line. As some cars with the charcoal filter removed you can smell petrol vapout in the car when at the lights.

I also have a weird idle problem at the moment.

The car used to idle at around 1300rpm when i was coming slowing down to stop and then go down to 900 when the car was stopped. Now it idles 1300rpm all the time when warm and around 1700rpm when cold, which wastes a shiload of petrol.

I have a pfc and the idels are set at 950rpm and 1200rpm or so for cold start.

Where is the idel control screw in the engine bay and is this meant to over ride the pfc settings?

where is the idel control valve located?

if its the same as an rb20 then its on the plenum near runner for cly #6 (called 'aac valve')

small square thing with a cylindrical thing attached. There should be a maroon plug going into it

remove the maroon plug

unscrew / tighten screw

replace maroon plug

idle changed!

just for the record (not sure if htis will help at all...):

i had htis issue where one day my car just started jumping idle from 500rpm to 2000rpm then stalled. Happened about 2 or 3 times on the same day.

When i got home, i got out the trusty old 'brake caliper cleaner' and cleaned the afm, took off the aac and gave it a clean, took off the O2 sensor and gave that a spray to remove any deposits on the probe, and reset the ECU

have never seen the weird idle problem again...

Cheers,

Waz.

  • 11 months later...

I think not .. as the guy below said, its for the vapour in the lines ..

which usually also reconnects to the intake so that the captured vapour can be sucked in by the engine again.

The charcoal filter is a filter for the air conditioning. It just simply filters the air so it is pure. However, it can end up slightly changing the idling of the car. It's nothing to worry about. I have the same problem on my R33, but it's severity varies.

I had the same problem in my R33.....

One of the small vacuum hoses had come off the little valve thing right next to the screw to let air out of the cooling system, towards the front of the engine above the fuel rail. Popped it back on, attached a clamp and the problem never came back.

Hope this helps....

Possible problems:

1. Air leak. Pinch the blow-by hose (the one connected to the intake plenum) and if the engine revs increase you probably have an air leak.

2. O2 sensor. At idle disconnect the O2 sensor and see if the hunting stops.

3. Plugs. Check condition.

Hope this helps.

Cheers

I have the same problem with my R32. I was stuffing around with air hoses on the weekend and now the revs bounce between 800 and 2000 when idling. Doubt it would be the charcoal canister as this only filters petrol vapours from the air. Guess I'll check air hoses around the plennum chamber.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
×
×
  • Create New...