Jump to content
SAU Community

Recommended Posts

advertising this one for a friend who is leaving the country very soon.

Yr/Make/Model

1999 Mirage

Engine hardware

6A12 Mivec

Engine accessories

Haltech E6K ECU, NGK racing plugs, RPW 6-2-1 extractors, K&N pod filter with CAI piping, High flow cat, 2.5" press bent exhaust from the extractor flange back. No resonators, one muffler. Two Davies Craig slimline thermo fans.

Drivetrain

Brass button clutch, FTO 5speed, diff, flywheel and driveshaft.

Brakes and suspension

Standard front discs with EBC green stuff pads. CK Lancer rear discs with EBC black stuff pads. Koni special adjustable shocks, Lovell lowering springs. Camber kit.

Rolling Stock

Momo Ferrari Engineering 16s. Pirelli PZnero rubber on front and P7000s on the back. 45 profile and 205 width. They've done about 5000kms so they're basically brand new! These tyres are worth close to $400 each...

Bodywork

deleted antenna, customised kit, PIAA spots, semi reflective tints, custom moulded GT4 bonnet scoop, aero mirrors

Interior

Sparco Torino seats, Momo tiller, Momo shifter, Momo gear boot, Sparco pedals, partially retrimmed door skins, electric windows, show install in boot.

Stereo

Panasonic DF800W CD/MP3 player, Infinity splits with MB Quart tweeters, running on a brand new Alpine 2x50wrms amp. Infinity Kappa Perfect 10" subs x2 running on a Response 4x100wrms amp. Sounds very loud and very crisp!

Its pretty quick, handles well and stops really well. A tad front heavy as you'd expect, but that was easily compensated for with a fat rear sway bar and a front strut brace (not coming with the car) It sounds mean and burbly due to the exhaust.

$15500 ONO

Any questions at all please call 0419 007 180 he is leaving the country very soon

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...