Jump to content
SAU Community

Recommended Posts

Is it true that there is a new law where it states that if you get defected for any illegal mods e.g BOV n shit....that not only do you get a fine, a defect notice but ALSO a demerit of points on your license?

One of my friends told me this but its the first time i have heard about this. anyone heard anything about this or have any idea what the penalties are for a defect?

I just installed my aftermarket Bov, and well i have 1 pt left on my license, so it would be pretty stupid if i lost my license again coz of a stupid BOV

so wana clear things up

GuiLty

Link to comment
https://www.sau.com.au/forums/topic/50921-loss-of-points-when-defected/
Share on other sites

it's well known now that atmo BOVs are defectable and the only BOV that you can have are the plumbacks. however most cops dont see it that way, and just all BOVs are illgeal in their eyes.

Guilty - just try to get everything legal and you shouldn't have any worries.

plumb back are the only legal bov but i know ppl have had plenty of arguments with cops over the matter, when they know a little bit about mods they are dangerous, it is much better when they know nothing coz then they just say, "it all looks ok"!!!!

is that for real? so if i get pulled over and done for my bov, pod, gauges, exaust and being dumped, then ive just lost 5 points? man i hope not. is it up to the cop weather or not he wants to take points or do u automaticaly just loose them?

dude.. you will loose a bare minimum of 1 point when you get a defect and its automatic. You should be ok for the pod.. well mine was fine... :D bov that depends on the cop, exhause and gauges yup. Tho as long as the gauges does not block your front view, ie below dash then they cant book you for it. Dumped.. yours look legal height man. :)

The final line is.. if the cop wants to book you, its done for unless you have the time and money to fight it.

The RTA and EPA are ****s. They can practically defect you for ANYTHING which isnt stock... You could have a plumb back and they can send you a EPA defect saying "Change Non Standard BOV". Its bullsh*t, and as for open atmosphere BOVs, they act like its venting poison... its just AIR!!!! sucking from under the bonnet and straight back into the bonnet without even going through the engine.. what a load of crap. I am lucky enough to never been defected but the previous owner of the car was *being smart ass too*. I really want to get an engineering slip for my car so I will have no worries about getting defect... I just hope all my mods will pass with an easy going mechanic engineer *think of import Lamborghini’s & other High end cars and they're twin turbos, big fat exhausts, roaring rich engines, & truck wide tyres, they're fine because they're Stock and Engineered that way....

My mate got defect for a broken tail light *lol, just like in the movies*, anyway the cops asked if they could pop the bonnet but they would have to sign something to do so... I thought this sounded quite odd that the cops couldnt pop his bonnet without getting permission, sorta like a search warrant for a house... I duno, i wasnt there, maybe its bullshit, but it doesnt sound right to me....

yeh thats true hey yotis, you went through a few hassles with ya wing diddnt u?

oh well lucky i have 12 points hey:)........umm i think, unless i did loose those 6 points from the burnout i did, apperntley i didnt cuase it was in nsw and i have qld liscense:)

It also comes down to the cop...If he's had a bad day or just has the urge to do some one over, he will, because he has the power...

Like every one above said, anything that didnt come with the car factory is considered a defect. I dont know if you guys heard or watched but there was this incident on tv with ray martin where a driver got defected for hanging one of those smelly trees under his revision mirror in the car....go figure....

cops are tops ;D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
×
×
  • Create New...