Jump to content
SAU Community

Recommended Posts

The drivers side power window has been slowly dieing and is now completely dead and wound all the way down too, so I can't really drive anywhere and leave it :D

I've pulled out the mechanism that all the buttons are on and checked the wires which visibly look ok, all other buttons on it are functioning fine.

Any ideas what parts I'm looking for, is the mechanism with all the buttons on it the actual motor or is that a seperate part?

TAI!

Link to comment
https://www.sau.com.au/forums/topic/50963-broken-drivers-power-window/
Share on other sites

Had the window been going down on a strange angle b4 that, i had the nylon roller break on me in the runners. Made up a new one b4 it put too much stress on winder motor. Also their may have been a loud bang if runner came out of balljoint. If not then i'd say ur motor is faulty. Cheers

most likely the switch....same problem happened to me. Because the switch was faulty (the drivers side has the 2mode switch...hold down/up to operate or just one touch for automatic) the switch would remain on and so burnt out the motor...so new switch and motor - $150 each. Then my switch needed to be rebuilt so add another $150. Note that there is a difference in switches...my '93 R33 series 1 switch was different to normal...something about a change is design between series....

Easiest way to find out would be to get a friends driver side button thingo, pull it out (its only 1 screw from inside the handle)unplug it and then plug it into your door. If its still no go then your window motor is fkt. My mate had a window motor replaced on his r33 but the guy didnt' put in a skyline one because he couldn't find one, so he popped in another window motor and the window used to go up like 3 times faster than a normal skyline window motor hehe.

same thing happened to me tonite. I used to hit da door quite a few times and it used to come up. But now i've tried everything and it won't go up. i'm hoping it is only the switch because it neva has a problem going down. but $150 for a new switch??? can i get dem ne cheaper??? or any way just to trick it back up and never use the window again?

my power window hasnt been workin for weeks now and its bloody anoying when u go drive thru or need to talk to someone. wat u do is flick the switch up a couple times till u hear the motor turn and then help it out by pulling up on the window with ur hand. or disconect the motor from the switch and run alternate power to it. mine didnt seem to work when i did that so i assume my motors stuffed not my switch.

JAPCAP -- any chance u could find out what motor that was?? im sure theres other motors out there that would fit. maybe 200sx motors??

  • 5 years later...

It always is the power window regulator and its a common problem (& no, it is not the switch). I replaced mine 3 years ago with a second hand one I found for 75$. Did it myself its not too hard. The damn thing just happened yet again n i got a quote for one and its going to be 195$ for the part now. Thinking of trying to repair the old one this time, its the little bit of carbon pad that gets worn off, the mechanism is completely find asides that. Its a very long shot, will let you know if I have any success with it.

post-75459-1280102457_thumb.jpg

had the same problem with my swich, found that the lever under the button to acivate the upward swich was broken, would go down fine but wouldnt go up. ended up buying another p/w swich for $50 havent had problems since

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
    • It's TWO steering wheels actually. 😛 one for each hand They are wheels, and they steer!
×
×
  • Create New...