Jump to content
SAU Community

Recommended Posts

I tend to use small brackets that screw into the underside of the top section of the bar and then are bent upwards, keeps the plate away from the bar. Works a treat. About 45cents each from bunnings

thats what i did too, except mines side mounted

Hey Guys and Girls;

I solved this problem with the slimline number plate mounts about a month after I got my R33 typeM. What you need to do is duck into a good mountain bike shop and buy your self two Minora water bottle holders and use the stainless steel mounting brackets to mount the plates. The bracket is exactaly the right width for the number plate holes and the bracket bolts straight onto the type M bar mounting the plate right smackbang in the middle of the center bar section that runs in the middle of the large opening of the bar.

Hope this helps

the 'Slimline plates' are a joke IMO. i went to get some today but found they're the exact same width as regular plates (i.e 372mm i think, the slot on my car is only about 350mm) Worst part is the only way to get a shorter width plate is to pay $627 (this is the ACT by the way) for custom plates!

What a joke! you can't have a standard number plate made shorter... and by the way, cutting them is illegal but go figure, the people down at the shopfront had NO IDEA about bent plates. Guess i'm just going to have to bring the plate forward. This is bloody stupid though, they should be able to make the plates shorter instead of stuffing around and paying $627 odd dollars for something i didn't want in the first place.

True they're Japanese plates, but how hard would it be to make our plates 25mm shorter? Honestly? is that too much to ask? obviously it is. one size, unless you want to get custom plates. Why make them slimmer and not shorter? that makes no damn sense.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...