Jump to content
SAU Community

Recommended Posts

Iputs more torque to front wheels, not sure of %age, but more than 50

Can't be more than 50%, ATTESSA hydraulic pump locks up the clucthes to the front wheels, rear wheels are always solidly connected. So at max pressure best is 50/50.

What does the centre diff button do next to the steering wheel?

Try it on wet grass. When turned off Stagea spins rear wheels for a bit and then feeds some torque to the front wheels and drives off. When turned on, it just drives off straight away, no waiting.

Very handy as the rear doesn't step out in the snow and ice. Not much use to me, no snow and ice in Sydney. Could be handy in the pits with the trailer on the back when it's wet though. The old Foulcan used to sit there spinning it's one rear wheel. Had to get towed to the sealed pit road once at Bathurst, very embarassing.

Just one more reason for choosing a Stagea :D

Link to comment
https://www.sau.com.au/forums/topic/51047-the-button/#findComment-1012070
Share on other sites

Hahahaha, good one SK, I can see it now, the old Foulcan smoking up one tyre in the pits and everyone looking thinking 'What the hell is he doing !!'...

Anyway, I just found this out last night as I was reading through heaps of Jap stuff on Stagea's.

With the button pressed in, the torque is 50/50 up to 20km/h. After 20km/h it sits at 80/20 (80% rear and 20% front) unless the front requires more, then it can vary up to 50/50.

Very interesting hay... You can see they were designed mainly for snow use (and would be great for pulling a boat out of the water at the boat ramp), and probably explains why you don't feel a big difference when driving normally with the button in.

J

Link to comment
https://www.sau.com.au/forums/topic/51047-the-button/#findComment-1012334
Share on other sites

jay do you know the addresses of the japanese sites you were looking at?

i searched google japan and yahoo japan and all the sites i keep finding are all the same stuff just the specs some pics of the guy/girls cars and mods etc...

looking for more interesting stuff like what you just posted

:D

Link to comment
https://www.sau.com.au/forums/topic/51047-the-button/#findComment-1012409
Share on other sites

jay do you know the addresses of the japanese sites you were looking at?

I actually got the link from Rezz's post on the thread you started :D The first link, but it was in a link in that link - if that makes sense !!!

Here's the first link;

http://homepage2.nifty.com/WGNC34/tuningdatetop.htm

You have to click on 'INDEX' for it to bring down a list of other links.

That particular info is the third link down in that link :) - here's the link;

http://homepage2.nifty.com/WGNC34/tuningdouryoku.htm

To read it you have to put it into a translator (bablefish won't work for some reason....). I use this translator http://www.systransoft.com/ after a while you have to register, but it's free.

Then in some sort of Japglish you can make this out at the bottom of the page;

"You handle for the reference and there is this kind of statement in the instruction manual.

At the time (usually time) of synchronizer mode OFF basis: 0: 100 MAX50: Variable control up to 50

At the time of synchronizer mode ON below (when departing) vehicle speed 20 km... 50: 50 fixing

Above (when travelling) vehicle speed 20 km... basis 20: 80 MAX50: Variable control up to 50."

J

Link to comment
https://www.sau.com.au/forums/topic/51047-the-button/#findComment-1012661
Share on other sites

good stuff jay thanks for the info

am trying to get my stagea site uploaded in the next couple of days

yeah babelfish is crappy i will try the systransoft program and see how i go :D

prank

good idea can you start one and maybe put the dash removal tutorial that shan posted a while back in there and sticky it??

:)

Link to comment
https://www.sau.com.au/forums/topic/51047-the-button/#findComment-1012693
Share on other sites

so this is a good feature to have when chopping holden utes at the traffic lights in the rain?

:);) ;)

Mate he was soooooo far behind, I leasurely changed lanes and drove along at the speed limit. Still took him a K or so to catch up. Subaru Forresters are also fun, they keep looking in the rear view mirror wondering why this strange waggon is keeping up. KEEPING UP, huh I was looking for room to go around. And then there was 4 guys in 2 WRX's that got whiplash when I went in between them in a roll on at the lights.

I have been having so much fun. :D

Link to comment
https://www.sau.com.au/forums/topic/51047-the-button/#findComment-1012695
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
    • Literally looks like direct port nitrous haha
×
×
  • Create New...