Jump to content
SAU Community

Recommended Posts

Hey all,

I have this continuing issue with my idle.

Here's the relavant hardware. PowerFC, standard MAF, standard injectors.

As water temperature approaches 80c the idle will go up to ~1300 and down to ~900.

It only does it when water temp approaches 80c. Under ~75 or so it's fine (as in it doesn't hunt - its constant). At 90c the fans come on and idle once again stabilises (constant).

When I play with the water temp correction values at 80c I can get it to hunt faster (it goes up and down faster) but I cannot get it to stay at one place.

Ideas/Suggestions?

P.S. I've seen a few post with people with similar type of problem. The difference is, mine only happens when it hits a certain temperature.

Thanks.

Mate, it's cause you drive a GTI-R!

lol.

:jk:

I've have never heard of that happening at just one small temp range. Maybe take it in to a good PFC tuner?

Best of luck - unstable idle is a pain in the ar$e.

Richard

Yer I found out the same to,when it was under electrical load eg lights heater etc it would hunt.Go into the idle setting and put the idle setting thats under the rev limit to 1270.it might be different for your car but I've played with all those idle settings and have mine idling perfect.

Richard, I did take it to a good PFC tuner to get tuned. I suppose they never picked up on it. How's the R and when's the R32 coming down?

R31 Power, I'll give that a go. I'll post what I find.

For those interested, while driving into work this morning stuck in traffic on the corner of LaTrobe and Spencer I turned O/2 Feedback "OFF". That fixed the hunting.

Go figure? I guess I could always switch between closed loop on/off with the hand controller depending on the situation.

Richard, I did take it to a good PFC tuner to get tuned. I suppose they never picked up on it. How's the R and when's the R32 coming down?

R31 Power, I'll give that a go. I'll post what I find.

For those interested, while driving into work this morning stuck in traffic on the corner of LaTrobe and Spencer I turned O/2 Feedback "OFF". That fixed the hunting.

Go figure? I guess I could always switch between closed loop on/off with the hand controller depending on the situation.

Hey Dandin,

It sounds like you may be on to something there. Possibly a faulty O2 sensor making the car not run nicely in closed loop? Does it exhibit any problems under light load cruise? or just idle?

Mate, the IR is better than it's every been, so of course I'm selling! All jokes asside, I'm really enjoying it at the moment - everything working as it should :) I am going to miss the little fella but the GTR should help ease the pain a tad!

Already buying up for the new car (just bought a PFC for it too). But it won't be here until december/january :)

It's a hard wait...

Richard

Actually, on cruise the O/2 sensor does it's job well. Cycles up and down nicely and frequently at highway speeds. And once again, the hunting only happens when temperature approaches 80c.

Enjoy the R32 mate. You owe me a spin next time I'm up your way.

Actually, on cruise the O/2 sensor does it's job well. Cycles up and down nicely and frequently at highway speeds. And once again, the hunting only happens when temperature approaches 80c.

Sounds like deffo a tunning prob then. Most likely not hardware.

Enjoy the R32 mate. You owe me a spin next time I'm up your way

thanks, and for sure mate you are most welcome anytime :) Only problem is you may find it a bit tame after stepping out of the pul-sah! Let me put the PFC I bought in + the neon cup holders, then we're cooking! :)

Richard

Hi there, your problem could well be the O2 feedback...not that its not working properly but because your car may not like a AFR of 14.7:1 when at idle during warm up .....My GTR does the same thing and got even worse when I put cams in .....I leave it turned off all the time now as I have done a lot of work on Light throttle cruise settings and have a constant 15:1 now on light throttles.

The o2 feedback, if switched on, comes into play once the engine temp reaches 70C on the GTR and this is when it starts the hunting. The temp for a GTI-R may be slightly different at which this occurs. During the 70c to 90c period the engine cylinder head is still coming up to operating temp during which time the engine would still be sensitive to a lean AFR of 14.7:1 and cause the symptoms you accurately described.

Once over 90C the fuel is atomising properly, instead of partially condensing on the back of the valve head and the idle will smooth out. One way around this is to increase the cold start temp compensation on the PFC at the 70C bracket and increase it gradually until the idle smooths out during this transition period. Or , as you;ve found, leave the O2 F/B turned off but if you do you had better make sure your tuner did a good job of the light throttles or expect fuel economy to go out the window :D

Hope this helps

MIke

R31 Power, I did as you suggested. No more hunting (even with O/2 feedback on). However, idle is now higher (something I can live with).

Mike, I will try what you have suggested and post up the results.

Thanks for the input people.

I had this same problem when I first installed my PFC. I found it was because I did not run with the A/C on for 10 min then headlights for 10 etc when I first started the car after installing the PFC.

Do you by any chance have an electric thermo fan. This could be your problem.

Do you by any chance have an electric thermo fan. This could be your problem.

R33vit, what dramas did you have with your thermo fan? Got one on my R32, when it kicked-in the Power FC started reading in the middle of the map, went bonkers? Is this what happened with yours? Still trying to rectify the problem.

No I dont have thermos but I had a electical load on and it would hunt. After I re initialized my PFC I followed the install manual step by step. If you do this you will lose your tune so take note of ALL the settings.

If it's been tuned with the FC Datalogit software then there may be other setting's you cant see and you'll lose them.

For those interested, while driving into work this morning stuck in traffic on the corner of LaTrobe and Spencer I turned O/2 Feedback "OFF". That fixed the hunting.

Go figure? I guess I could always switch between closed loop on/off with the hand controller depending on the situation.

if that fixed it, your O2 sensor is rooted.

just change it.

Mine does exactly the same thing, once it gets hot. So we've turned off the O2 till i buy another. It will only hurt economy, nothing else in the mean time.

-ash

Ash, thanks for the tip.

But here's something. Hwy driving between ACT/Melb I was getting close 600km per tank (on a 50 litre tank). I get about 350-450km per tank city driving with the occisianal heavy right foot (pending on how heavy my foot gets).

Either way, I'll think about changing the O/2 sensor down the line.

Mike (The Alchemist) - Where in the PFC menu do I change "cold start temp compensation"?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...