Jump to content
SAU Community

V-mounting intercooler

redline2003

By redline2003,
in Engines & Forced Induction

 Share

Recommended Posts

funkymonkey Grand Master

funkymonkey

Posted
Posted

hehe would push the intercooler into the engine.... its real tight in a skyline enginebay as it is. with an SR conversion it'd be awesome, but I don't see many advantages in a skyline engine bay with an RB. real estate front to back is real tight in one of those. Didn't really think about the heat rising from the radiator...

Ive been a fan of the open V mount... ie radiator vertical behind the intercooler which is on an angle with a bonnet vent... but the V mount on the R31 is interesting... for race use only I guess.

If you wanted to be a real tricky dicky you'd make the whole thing out of flexible piping and mount some servo's to move the radiator and Intercooler from vertical to V mount according tot he speed you were goin at... :D hmmm now there's an idea...

dangerous_daveo Grand Master

dangerous_daveo

Posted
Posted
.....

If you wanted to be a real tricky dicky you'd make the whole thing out of flexible piping and mount some servo's to move the radiator and Intercooler from vertical to V mount according tot he speed you were goin at... :D hmmm now there's an idea...

LoL all the gain you got from the shoter pipes etc, you would lose in tricky electronic gear :P

dangerous_daveo Grand Master

dangerous_daveo

Posted
Posted
what if you leave the radiator as is and mount the ic on top of the engine(possibly a sm but thicker radiator to compensate that way the fans can still suck air through the radiator and pull air through the intercoller, best of both worlds?

K

Like a subaru?

aybee Experienced

aybee

Posted
Posted
Yep, but the hot air comes up from the radiator and goes through the intercooler and out the bonnet (ie; hot air rises) On its way though the hot air heats up the intercooler.  That never happens with a FMIC, the radiator is behind the intercooler and the engine or electric fan sucks the hot air from the radiator, away from the intercooler.

In a > mount in traffic or stationary, the intercooler will quickly get to 90 degrees, which is the temperature of the air coming out of the radiator.  It will cool down once you get moving, that why it is an OK setup in a race car.  But a waste of time and money in a road car.

Oh and you should see the damage if you have a slight front end tap, makes a real effenn mess. :D

but at idle the turbo is not running any boost. so it wouldnt really matter would it? as soon as you start moving the superior air flow would cool it down pretty quickly. wouldnt it?

.

Sydneykid Grand Master

Sydneykid

Posted
Posted
but at idle the turbo is not running any boost. so it wouldnt really matter would it? as soon as you start moving the superior air flow would cool it down pretty quickly. wouldnt it?

.

Ahh no, the intercooler is still hot, so it heats up the air going through it. Until it cools down, maybe 2 to 10 seconds depending on speed and ambient air temp. :D

Craved Grand Master

Craved

Posted
Posted

This is what i'll be running in the lancer project im working on ATM, however the is no reason that the intake itself cannot be partitioned right from the intake itself, running a thermo fan on both the radiator and the intercooler! separate intake ans thermo's fresh air at any speed to both cooling devices!

OH and whats wrong with running the radiator at the top to stop further heat soak????

i will be keeping an eye on this thread for sure!

GTR-NUTTER - that would defeat the purpose.. they want separate intakes for both devices, so a conventional IC with horizontal radiator would still be heated by the IC before the rad!

dangerous_daveo Grand Master

dangerous_daveo

Posted
Posted
....

OH and whats wrong with running the radiator at the top to stop further heat soak????

.....

I guess because that kills the idea of having shorter piping???

Which brings me to my next question, does taking out that little amount of piping have that much effect???

Craved Grand Master

Craved

Posted
Posted

that could be true, but it would depend on what engine the car was using! if say it was a front facing plenum then the IC on top wouldn't really affect the pipe length compared to below....

however a standard rb25 inlet manifold would best be used with the IC on top, this i pressume wouldn't be the case if going to the length of ">" mounting these coolers!

better response from throttle on/off, and minimal chance of heat soaking the pipes (not an issue really within the pipes only IC core)

dangerous_daveo Grand Master

dangerous_daveo

Posted
Posted

But if you have the money to throw around on > mounting stuff, then you probably have the money for better forward facing plenums, and internals, and turbos, etc etc :mad: Either that or WAYYYY tooo much time on your hands.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Blue/grey smoke after idle

      By sunsetR33 · Posted

      Can't you put the pistons to TDC and then do the valve seals? Or will the drop down too far to pull them back up?
    • sunsetR33
      Replacing turbo water line - any recommendations or advice?

      By sunsetR33 · Posted

      One thing I can tell you is, do it properly the first time. If you encounter unexpected problems just let the car sit for a week or two if you have to get some other parts or figure stuff out.  I'd have said go and use as many OEM parts as possible but since you want to change the turbo later on a custom kit is probably the better choice. Since I have no experience with RB25 just compare parts diagrams and images before buying a line kit and it should be easy to see if it has everything you need. Amayama has very good parts diagrams and part number lists, that is what I used a bunch to figure out what I might need. And don't forget to plan ahead and possibly renew other stuff that's easy to get to while you're in there doing the turbo lines. Happy wrenching
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 4:   Hi all, good news. Engine is running and all the gaskets and seals seem to be working as intended. No leaks so far, even the JB Weld seems to hold. I flushed out the old coolant a few times and put in fresh coolant, not Nissan stuff, I decided to try the Ravenol Protect FL22, they claim it works for a wide variety of JDM cars and the opinions on it by some people were pretty good. And it has the nice poison green color! And man am I glad I bought a coolant system tester earlier this year, vacuum filling works wonders on this engine. I can definitely recommend this to anyone still doing it the old school way. All you need is compressed air supply. Will have to do a small test drive as soon as I can, I removed the gauge cluster again as the tacho needle was still bouncing around a bit but it was much better than before already.  I also found some cracks on all 4 tires inner and outer sidewalls. Apparently these tires should 't be parked on for extended periods or be kept under 0 degrees during storage, which I did not know. Clearly the previous owner didn't look into those details either, he probably bought them just cause they are cool semi-slicks. I'm just wondering how tf I am supposed to reach 30-80 degree tire temperatures on the public road consistenly, these tires were never going to work for my use case. I'll probably order Continental SportContact7 ones as these are the best allround summer tire available right now and I don't think I'll need anything crazier for now. Do let me know if you have experience with various tires and which ones you recommend.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      You have no idea how many goddamn boxes I received these past three months haha Most have been put to use by now though, luckily
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Not going to pretend I didn't do a bit of junky work this time around, but mostly due to the fact that some things I am not willing to spend days fixing right now, like wiring. I try to do most things properly the first time around.
×
×
  • Create New...