Jump to content
SAU Community

Recommended Posts

I am going to rebuild my block over the winter, since it leaned out and my rings or ring lands went out. I am going forged pistons, rings, ARP head studs, and metal head gasket. The setup should be good to a little over 600hp with ease. My question is that I don't have that much money and am affraid that I am spending it all on the motor getting rebuilt and a bigger turbo with a few other goodies (FMIC, 720-850cc injectors, etc....).

My question to you guys is that I know the Q45 MAF can handle right around 600hp, but will an Apex'i SAFC or ROM tunned ecu handle those numbers?

What is the SAFC good to?

Also does anyone have another method or idea?

I just don't have the money to get an expensive stand alone (PowerFC, Link, Haltech, etc......)

Help would be greatly appreachated....thanks

Link to comment
https://www.sau.com.au/forums/topic/51770-fuel-managment500-600hp/
Share on other sites

a safc will be able to take u to a certain point where aftermarket management is needed

just dont go running 2 bar boost or something crazy

safc will do for the time but u really need to be doing a/f, timing etc to really achieve the best reliable results

so the SAFC is capable of 500-550hp?

I have not really seen that many use it after they get around 450+, but then agian those that have the money to achieve 500-600hp normally have the money to go stand alone. I do not though. I do plan on getting a Power FC sooner or later, but will not have the money right away.

I will have an SAFC and a adjustable FPR....and am hoping to acheive 500-500hp, if possible. Would like to hear everyones opinion first and see if it is possible.

I am going to rebuild my block over the winter, since it leaned out and my rings or ring lands went out. I am going forged pistons, rings, ARP head studs, and metal head gasket. The setup should be good to a little over 600hp with ease. My question is that I don't have that much money and am affraid that I am spending it all on the motor getting rebuilt and a bigger turbo with a few other goodies (FMIC, 720-850cc injectors, etc....).  

My question to you guys is that I know the Q45 MAF can handle right around 600hp, but will an Apex'i SAFC or ROM tunned ecu handle those numbers?

What is the SAFC good to?

Also does anyone have another method or idea?

I just don't have the money to get an expensive stand alone (PowerFC, Link, Haltech, etc......)

Help would be greatly appreachated....thanks

SAFC only adjust A/F ratios in pretty broard steps at that when used on a 600 bhp engine. It does NOTHING for igntion timing, in fact in many cases an SAFC makes the ignition timing problem worse. Following is a previous post of mine explaining why......

a quick, simplistic explanation of how an SAFC works might help...

As the airflow into the engine increase, the AFM records this as increased voltage that the ECU sees. What an SAFC does is sit in between the AFM and the ECU and take the voltages from the AFM and either increase or decrease them depending on what you have programmed the SAFC to do. By increasing the voltage, this tricks the ecu into pumping in more fuel, you do this when the engine is running lean. By decreasing the voltage, this tricks the ecu into pumping in less fuel, you do this when the engine is running rich.

The next bit is hard to understand unless you remember that the standard ecu does not supply fuel in direct proportion to the afm voltage ie; 4 volts is not twice as much fuel as 2 volts. Engine rpm, boost and throttle position also help the ecu determine how much fuel to add.

It has been my experience that RB25's run a little lean down low in the rpm range (Nissan do this for fuel economy and emissions) and a lot rich up high (Nissan do this to protect the engine). So I have to increase the voltage (using the SAFC) up to around 3,000 rpm (part throttle especially) and decrease the voltage over 5,000 rpm (full throttle).

The real problem is in the 3,000 to 5,000 rpm range as the engine comes on boost. They really need lots of fuel very quickly in this area. This can mean that you need to increase the voltage (that the ecu sees) over 5.1 volts to get the right A/F ratios. The ecu then goes into engine protection mode, rich and retarded (sounds like a girl I knew once) . Past that rpm you can start leaning it out as it runs too rich, so the voltage needs to be turned down under 5.1 volts. The ecu sees this as the engine not needing protection mode any more, no more rich and retarded.

It is not unusual to get good performance up to 3,000 rpm, then sluggish from 3,000 rpm to 5,000 rpm and then good performance from 5,000 rpm and over. The SAFC may not help this, in fact as explained above, it can in fact make it worse if the tuner is not switched on to this stuff.

With bent afm voltages, the ecu (tricked by the SAFC) also fires the ignition to suite the airflow it THINKS the engine is getting. This is not a good thing as you generally end up with ignition that is too far advanced in some rpm ranges.

The poor tuner has to juggle the SAFC settings, so that the A/F ratios are OK, the ecu doesn't get into rich and retard (engine protection) mode and the ignition timing is not too far advanced so as to cause detonation. My experience (I am not a good tuner) has been that this is full of compromises, sometimes you just can't win and have to reduce the boost level a bit to get even a reasonable compromise.

Keep in mind that this explanation is very simplified to make it fit in a reasonable space, the rpm's used are rough guides only and every car is different.

Hope it helps (and makes some sense). :D

Thanks for the info sidneykid, I know what the SAFC does and how it works, just wasn't sure where people have taken it (max hp). I know a few shops here in the states have taken it a little past 450hp....just checking if anyone has taken it past the 500hp mark.

Do you guys think it will be safe to use the SAFC and Q45 maf to 450hp and then in the near future get a power fc and tune it to my 600hp goal?

Has anyone used the ROM tune on their ecu?

If you use an Safc to lean out your car it also advances the timing and if you richen it it will retard the timing as it is tricking the ECU to think it is under more or less load so be careful.

Laptop tunable ECUs are only 1395 now and compared to a 600+hp motor thats cheap.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...