Jump to content
SAU Community

Recommended Posts

Ok, so I'm bored at work.

I called up their customer service line 1300 134 555 option 3 then 1. Basically they couldn't tell me much.

Optimax apparently comes from only one refinery. The newport refinery. I tried to bait them into saying that there were either issues at the refinery, or issues with delivery. They didn't take the bait.

Ah well, that was fun. It relieved the boredom of work for a few minutes. :D

wil..

every where I have been today has been good, castlhill,baulkham hills, west ryde.. they all got around $1.12-$1.00..havent filled up for a while.. my car seemed gratefull afterwards lol :D

  • 2 weeks later...

This is the reply I got from Shell Australia today via email

Dear Edward,  

Thank you for contacting Shell Australia.  

In relation to your enquiry, the shortage of fuels recently has been caused by an unscheduled maintenance  shutdown at our Newport tank terminal. This has caused severe shortages of all  fuels.

The plant is now back on stream, however we anticipate it will take a few more days for  our drivers to  complete the back log of deliveries to  sites.  

It may be that some sites run out of product before the tankers can get back to them.  

We apologise sincerely for the inconvenience this has caused. Please be assured our plant managers and drivers are working around the clock to ensure  consistency of supply as best they are able.

I trust this has been of assistance to you.  

Regards  

Patricia O'Reilly  

Tell Shell Australia  

PH: 1300 134 555  

Well their is two places (in the World) were they cant sell Optimax and I found out WA is one of them, we only use Ultimate from BP over here, when I lived in Newcastle we always used Mobil's Premium as it is 98.8 to 98.9 (I drove tankers for 6 years and ran a fuel storage area so I learnt a bit about fuel).

One of the Japanese motorcycle builders told buyiers not to use Optimax in one of their up market bikes.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
    • -10 is plenty for running to an oil cooler. When you look at oil feeds, like power steering feeds, they're much smaller, and then just a larger hose size to move volume in less pressure. No need for -12. Even on the race cars, like Duncans, and endurance cars, most of them are all running -10 and everything works perfectly fine, temps are under control, and there's no restrictions.
    • Update: O2 sensor in my downpipe turned out to be faulty when I plugged in to the Haltech software. Was getting a "open circuit" warning. Tons of carbon buildup on it, probably from when I was running rich for a while before getting it corrected. Replaced with new unit and test drove again. The shuffle still happens, albeit far less now. I am not able to replicate it as reliably and it no longer happens at the same RPM levels as before. The only time I was able to hear it was in 5th going uphill and another time in 5th where there was no noticeable incline but applying more throttle first sped it up and then cleared it. Then once in 4th when I slightly lifted the throttle going over a bump but cleared right after. My understanding is that with the O2 sensor out, the ECU relies entirely on the MAP tune and isn't able to make its small adjustments based on the sensors reading. All in all, a big improvement, though not the silver bullet. Will try validating the actuators are set up correctly, and potentially setting up shop time to tune the boost controller on closed loop rather than the open loop it is set to now. Think if it's set up on closed loop to take the O2 reading, that should deal with these last bits. Will try to update again as I go. 
    • More so GReddy oil relocation kits, sandwich plates, etc. all use 10AN fittings. And same, I've only used 10AN and my car sees track work (circuit, doing laps, not 10 sec squirt business).
×
×
  • Create New...