Jump to content
SAU Community

aftermath of fri night


copbait
 Share

Recommended Posts

Your so right, who gives a rats arse if its fair or not, just do as you are told, good boy - appathetic attitudes really piss me off - maybe you should become a cop, you seem to think that they are right regardless.

Fact - the SA POL DO NOT ENFORCE THE LAW, WITH REGARDS TO THE ROAD TRAFFIC ACT CORRECTLY,  

Fact - TPT SA DO NOT ENFORCE VEHICLE STANDARDS CORRECTLY.

I have had enough of these forums

Take care all.

All the Road Traffic Act and Road Traffic Regulations say with regard to ride height is it has to meet ADRs and have a minimum 100mm clearance. How is that wrong or harsh?

Link to comment
Share on other sites

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

Your so right, who gives a rats arse if its fair or not, just do as you are told, good boy - appathetic attitudes really piss me off - maybe you should become a cop, you seem to think that they are right regardless.

Fact - the SA POL DO NOT ENFORCE THE LAW, WITH REGARDS TO THE ROAD TRAFFIC ACT CORRECTLY,  

Fact - TPT SA DO NOT ENFORCE VEHICLE STANDARDS CORRECTLY.

I have had enough of these forums

Take care all.

OOOOK......................

Hey, this is reality and they are the RULES and regulations that govern this state. If you dont like it, do your little bid to fight their bullshit like you attempted to last time. Me personally, Ill do my best to keep my cars 'looking' legal. And the one that doesnt, ill just play the game of staying away. There are more serious matters in life to be whinging about defects on an obviously defective car. By the way, how did your little fight against TSA end up again????? :talk2hand

Link to comment
Share on other sites

All the Road Traffic Act and Road Traffic Regulations say with regard to ride height is it has to meet ADRs and have a minimum 100mm clearance. How is that wrong or harsh?

Then there's the 1/3 of suspension travel, then there's the minimum height your headlights must sit... If they don't get you on one thing they will get you on another *when they want to*.

Link to comment
Share on other sites

Adam,

I actually hav'nt looked at the reg's for sa. however i do know that a 100mm block is passed under your car at a regency pk inspection and cannot foul anthing under your car-eg:exhaust, handbrake cables, electrical cables or suspension components etc..

Regards,

SKYLINE(Kym).....

Link to comment
Share on other sites

Adam,

       I actually hav'nt looked at the reg's for sa. however i do know that a 100mm block is passed under your car at a regency pk inspection and cannot foul anthing  under your car-eg:exhaust, handbrake cables, electrical cables or suspension components etc..

      Regards,

                  SKYLINE(Kym).....

When did I say it wasn't 100mm? I've said it is twice! It can foul under the car on a few things though

Ground clearance

 73. (1) In this rule:

 

"ground clearance", of a vehicle, means the minimum distance to the ground from a point on the underside of the vehicle, except a point on a tyre, wheel, wheel hub, brake backing plate or flexible mudguard or mudflap of the vehicle.

 

 (2) A motor vehicle or combination must have a ground clearance of:

 

(a)at least 100 millimetres at any point within 1 metre of an axle; and

 

(b)at least one‑thirtieth of the distance between the centres of adjacent axles at the midpoint between them; and

 

©at any other point—at least the distance that allows the vehicle or combination to pass over a peak in the road with a gradient on either side of 1:15, if the wheels of 1 axle of the vehicle or combination are on the slope on one side of the peak and the wheels of the next axle are on the slope on the other side.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Does this count as a time trial as well? I got all gold in the master super licence (1 lap time trial) and received a McLaren MP4/4 for my trouble.  If anyone else has done this, did you ride the wall right around the first long right hander at Lake Louise snow track to get gold? I couldn't do it any other way... best I could do without riding the was was within 2 tenths of the gold time.
    • I definitely get the low power, sporty car to drive to smash gears but not be doing eleventy million miles an hour! It makes all the normal drives fun!   Rev match tune sounds like the funs! I didn't know the NC had a DBW throttle!   As for me, still have the Skyline, it still has the Barra in it. It's been pushed to the side of the workshop at the moment. Pretty much waiting on me finishing the wiring, and dropping new fuel lines in. Got myself an ACDC Tig end of last year so been teaching myself TIG welding to build a few things for the Skyline. The missus wrote off her GTB liberty at the end of last year, and got it back on salvage rights stupid cheap. It's also still registered, so will mean easier for me to take to the track already done most of the panel damage, just playing "clear the workshop" to make space to pull the motor and box out, fix some oil leaks, replace the clutch, and replace a few minor broken things.  Also got a Lathe at the start of the year, which is adding to the annoyance of no space, which is another reason I'm trying to build things to get more space, to get the Lathe back in a final home for it. It's a BIG lathe, can turn a 355mm diameter, and 1metre between centres... Got it at a steal! So between it and the TIG and old MIG welder, I'll be fabbing some fun little shit up But we've had a lot of shit stuff happening at home, so it's slow going getting things done. But one step at a time!
    • I love Catalunya.  Got a 1:54.632. The AMG is a hoot.
    • I hadn't got that far, my main worry was the connection to the actual calipers themselves. I'm just using new (ish) stock brake lines in the stock setup. I've just had a stud welded to the knuckle that is a little lower than the original stud (so my knuckles have two studs each side) to not have it be stretched so far in previous BBK setups, so the "block" (in the second picture) mounts a little lower for me and I hope I don't need to change anything. I may have even changed the connection to the calipers in the past and have since forgotten I did that. I may not have. Guess how I'm gonna find out. Source: hopium
    • It's more so I'm using the 1x piece line from HEL that goes from the body to the caliper. There's no middle block/mount like the HFM ones or the GKtech ones. There are certain angles/suspension compression where the line actually slightly contacts the ARB. Below of how mine sit (not my photo): How I want it:  
×
×
  • Create New...